Optimization of Machining Parameters for Minimization of Roundness Error in Deep Hole Drilling using Minimum Quantity Lubricant

被引：2
|
作者：
Kamaruzaman, Anis Farhan [1 ]
Zain, Azlan Mohd [1 ]
Yusof, Noordin Mohd. [2 ]
Nadjarian, Farhad [2 ]
机构：
[1] Univ Teknol Malaysia, Fac Comp, Soft Comp Res Grp, Skudai 81310, Johor, Malaysia
[2] Univ Teknol Malaysia, Fac Mech Engn, Skudai 81310, Johor, Malaysia
来源：
2ND INTERNATIONAL CONFERENCE ON GREEN DESIGN AND MANUFACTURE 2016 (ICONGDM 2016) | 2016年 / 78卷
关键词：
INCONEL; 718; SYSTEM;
D O I：
10.1051/matecconf/20167801024
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
This paper presents an experimental investigation of deep hole drilling using CNC milling machine. This experiment investigates the effect of machining parameters which are spindle speed, feed rate and depth of hole using minimum quantity lubricant on the roundness error. The experiment was designed using two level full factorial with four center point. Finally, the machining parameters were optimized in obtaining the minimum value of roundness error. The minimum value of roundness error for deep hole drilling is 0.0266 at the spindle speed is 800 rpm, feed rate is 60 mm/min, depth of hole is 70 mm and minimum quantity lubricant is 30ml/hr.
引用
收藏
页数：6
相关论文
共 50 条
  • [1] Characterization of Cutting Parameters in the Minimum Quantity Lubricant (MQL) Machining Process of a Gearbox
    Travieso-Rodriguez, J. A.
    Gomez-Gras, G.
    Garcia-Vilana, Silvia
    Mainau-Noguer, Ferran
    Jerez-Mesa, R.
    INTERNATIONAL JOURNAL OF MANUFACTURING MATERIALS AND MECHANICAL ENGINEERING, 2015, 5 (01) : 49 - 60
  • [2] Optimization of the small and deep hole drilling parameters
    Li, SJ
    Zhang, PK
    PROGRESS OF MACHINING TECHNOLOGY: WITH SOME TOPICS IN ADVANCED MANUFACTURING TECHNOLOGY, 2000, : 673 - 677
  • [3] A study of drilling performances with minimum quantity of lubricant using fuzzy logic rules
    Nandi, Arup Kumar
    Davim, J. Paulo
    MECHATRONICS, 2009, 19 (02) : 218 - 232
  • [4] Machining Parameters Optimization on Micro Hole Vibration Drilling Using Grey System Theory
    Lai, Xingyu
    Yan, Chunyan
    Zhan, Chunyi
    Ye, Bangyan
    Li, Weiguang
    2015 IEEE INTERNATIONAL CONFERENCE ON MECHATRONICS AND AUTOMATION, 2015, : 2307 - 2312
  • [5] Optimization of machining parameters for kerf angle and roundness error in abrasive water jet drilling of CFRP composites with different fiber orientation angles
    Meltem Altin Karataş
    Ali Riza Motorcu
    Hasan Gökkaya
    Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2020, 42
  • [6] Optimization of machining parameters for kerf angle and roundness error in abrasive water jet drilling of CFRP composites with different fiber orientation angles
    Karatas, Meltem Altin
    Motorcu, Ali Riza
    Gokkaya, Hasan
    JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING, 2020, 42 (04)
  • [7] Improvement in machining process performance using solid lubricant assisted minimum quantity lubrication
    Makhesana, Mayurkumar A.
    Patel, Kaushik M.
    ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2022, 8 (02) : 2102 - 2127
  • [8] Small deep hole drilling electro discharge machining process optimization using Taguchi method
    Jimenez-Chavarro, Guillermo
    Jose Vieira-Porto, Arthur
    Hideaki-Tsunaki, Roberto
    REVISTA FACULTAD DE INGENIERIA, UNIVERSIDAD PEDAGOGICA Y TECNOLOGICA DE COLOMBIA, 2016, 25 (42): : 111 - 122
  • [9] ON THE PREDICTION OF THE ROUNDNESS ERROR IN BTA DEEP HOLE MACHINING BASED ON THE STOCHASTIC DESCRIPTION OF THE CUTTING TOOL MOTION.
    Chandrashekhar, S.
    Ahmad, Z.
    Sankar, T.S.
    Osman, M.O.M.
    International Journal of Production Research, 1986, 24 (04): : 879 - 899
  • [10] ON THE PREDICTION OF THE ROUNDNESS ERROR IN BTA DEEP HOLE MACHINING BASED ON THE STOCHASTIC DESCRIPTION OF THE CUTTING-TOOL MOTION
    CHANDRASHEKHAR, S
    AHMAD, Z
    SANKAR, TS
    OSMAN, MOM
    INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH, 1986, 24 (04) : 879 - 899
12345