Stable high-nickel austenitic steel produced by electron beam additive manufacturing using dual wire-feed system

被引：7
|
作者：
Moskvina, V. A. [1 ]
Melnikov, E. V. [1 ]
Astafurov, S. V. [1 ]
Panchenko, M. Yu. [1 ]
Reunova, K. A. [1 ]
Kolubaev, E. A. [1 ]
Astafurova, E. G. [1 ]
机构：
[1] RAS, Inst Strength Phys & Mat Sci SB, 2-4 Akad Skii Ave, Tomsk 634055, Russia
来源：
MATERIALS LETTERS | 2021年 / 305卷
关键词：
Stainless steel; NiCr alloy; Additive manufacturing; Austenite; Microstructure; STAINLESS-STEELS;
D O I：
10.1016/j.matlet.2021.130863
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Phase composition, microstructure, tensile properties and fracture mechanism of the high-nickel austenitic steel produced by a dual wire-feed electron beam additive manufacturing were studied. The joint using of NiCr-alloy and 321-type stainless steel wires in additive manufacturing process assists the formation a fully austenitic structure in as-built billet. Its microstructure is stable against deformation-induced gamma -* alpha' martensitic transformation due to the 5-7 wt.% increase of nickel concentration relative to the initial steel wire composition. The high-nickel steel possesses high ductility (6 approximate to 54%) and plastic flow behavior similar to the conventional cast 321-type steel subjected to a solid-solution treatment.
引用
收藏
页数：4
相关论文
共 50 条
  • [21] Defects Formation Features of Nickel-Based Superalloy Product Obtained by Wire-Feed Electron Beam Additive Manufacturing
    Gurianov, D. A.
    Fortuna, S. V.
    Osipovich, K. S.
    PROCEEDINGS OF THE INTERNATIONAL CONFERENCE ON ADVANCED MATERIALS WITH HIERARCHICAL STRUCTURE FOR NEW TECHNOLOGIES AND RELIABLE STRUCTURES 2019, 2019, 2167
  • [22] Characterization of Microsegregation and Secondary Phase Precipitation in Nickel-Based Superalloy after Wire-Feed Electron Beam Additive Manufacturing
    D. A. Gurianov
    S. V. Fortuna
    S. Y. Nikonov
    E. N. Moskvichev
    E. A. Kolubaev
    V. E. Rubtsov
    P. S. Sokolov
    Russian Physics Journal, 2022, 65 : 1396 - 1403
  • [23] Microstructure, Phase Composition, and Microhardness of the NiCr/Al Gradient Material Produced by Wire-Feed Electron-Beam Additive Manufacturing
    Reunova, K. A.
    Zagibalova, E. A.
    Astapov, D. O.
    Astafurov, S. V.
    Kolubaev, E. A.
    Astafurova, E. G.
    RUSSIAN PHYSICS JOURNAL, 2023, 66 (03) : 341 - 349
  • [24] Characterization of Microsegregation and Secondary Phase Precipitation in Nickel-Based Superalloy after Wire-Feed Electron Beam Additive Manufacturing
    Gurianov, D. A.
    Fortuna, S. V.
    Nikonov, S. Y.
    Moskvichev, E. N.
    Kolubaev, E. A.
    Rubtsov, V. E.
    Sokolov, P. S.
    RUSSIAN PHYSICS JOURNAL, 2023, 65 (8) : 1396 - 1403
  • [25] Microstructure, Phase Composition, and Microhardness of the NiCr/Al Gradient Material Produced by Wire-Feed Electron-Beam Additive Manufacturing
    K. A. Reunova
    E. A Zagibalova
    D. O. Astapov
    S. V. Astafurov
    E. A. Kolubaev
    E. G. Astafurova
    Russian Physics Journal, 2023, 66 : 341 - 349
  • [26] Obtaining of Bimetallic Product from Nickel Superalloy and Heat-Resistant Bronze by Wire-Feed Electron Beam Additive Manufacturing
    A. V. Chumaevskii
    E. A. Kolubaev
    K. S. Osipovich
    D. A. GurIanov
    V. E. Rubtsov
    S. Yu. Nikonov
    A. E. Boltrushevich
    Russian Physics Journal, 2022, 65 : 1231 - 1238
  • [27] OBTAINING OF BIMETALLIC PRODUCT FROM NICKEL SUPERALLOY AND HEAT-RESISTANT BRONZE BY WIRE-FEED ELECTRON BEAM ADDITIVE MANUFACTURING
    Chumaevskii, A. V.
    Kolubaev, E. A.
    Osipovich, K. S.
    GurIanov, D. A.
    Rubtsov, V. E.
    Nikonov, S. Yu.
    Boltrushevich, A. E.
    RUSSIAN PHYSICS JOURNAL, 2022, 65 (07) : 1231 - 1238
  • [28] Regularities of the Formation of the Polymetallic Samples of the Fe-Ti, Fe-Cu-Ti System, Produced by the Wire-Feed Electron Beam Additive Manufacturing
    Osipovich, K. S.
    Kalashnikov, K. N.
    PROCEEDINGS OF THE INTERNATIONAL CONFERENCE ON PHYSICAL MESOMECHANICS. MATERIALS WITH MULTILEVEL HIERARCHICAL STRUCTURE AND INTELLIGENT MANUFACTURING TECHNOLOGY, 2020, 2310
  • [29] Elastic modulus and hardness of Ti alloy obtained by wire-feed electron-beam additive manufacturing
    Klimenov, Vasiliy
    Kolubaev, Evgeny
    Han, Zeli
    Chumaevskii, Andrey
    Dvilis, Edgar
    Strelkova, Irina
    Drobyaz, Ekaterina
    Yaremenko, Oleg
    Kuranov, Aleksandr
    OBRABOTKA METALLOV-METAL WORKING AND MATERIAL SCIENCE, 2023, 25 (04): : 180 - 196
  • [30] Process planning for laser wire-feed metal additive manufacturing system
    Ding, Yaoyu
    Akbari, Meysam
    Kovacevic, Radovan
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 95 (1-4): : 355 - 365
12345