Study on fibre orientation of weld line parts during injection moulding of fibre reinforced plastic by image processing

被引：18
|
作者：
Kim, J. W. [2 ]
Kim, H. S. [3 ]
Lee, D. G. [1 ]
机构：
[1] Chosun Univ, Dept Mechatron Engn, Kwangju 501759, South Korea
[2] Iowa State Univ, Ctr NDE, Ames, IA 50011 USA
[3] Chosun Univ, Grad Sch, Dept Adv Parts & Mat Engn, Kwangju 501759, South Korea
来源：
MATERIALS RESEARCH INNOVATIONS | 2011年 / 15卷
关键词：
Injection moulding; Fibre orientation function; Fibre content ratio; Image processing; FRP; Weld line; FRP;
D O I：
10.1179/143307511X12858957674274
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In injection moulded products using fibre reinforced plastics, weld line was unavoidable due to mould shaping factors such as the position and size and number of mould gates. The weld line leads to fibre orientation perpendicular to resin flow direction, sudden reduction of the reinforcement effect and consequently degrading of the mechanical properties of moulded products. Until now, there has been no research on the measurement of fibre orientation in the weld line using image processing. Using the image processing method, the fibre orientation distribution of weld line in injection moulded products was assessed. The effects of fibre content and injection mould gate conditions on the fibre orientation were also discussed.
引用
收藏
页码：S303 / S306
页数：4
相关论文
共 50 条
  • [41] Comparison between computed and measured fibre orientation in injection moulded parts
    Kech, A.
    Vincent, M.
    INTERNATIONAL JOURNAL OF MATERIAL FORMING, 2008, 1 (Suppl 1) : 747 - 750
  • [42] COMPRESSIBILITY OF CHOPPED FIBRE-REINFORCED PREPREGS DURING COMPRESSION MOULDING
    Sentis, D. Ferre
    Orgeas, L.
    Dumont, P. J. J.
    du Roscoat, S. Rolland
    Sager, M.
    20TH INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS, 2015,
  • [43] Image analysis method for estimating 2-D fibre orientation and fibre length in discontinuous fibre reinforced composites
    Pourdeyhimi, B.
    Ramanathan, R.
    Polymers and Polymer Composites, 1995, 3 (04): : 277 - 287
  • [44] High fibre volume fraction injection moulding of carbon fibre reinforced polyetheretherketone (PEEK) in order to raise mechanical properties
    Semadeni, M
    Zerlik, H
    Rossini, P
    Meyer, J
    Wintermantel, E
    POLYMERS & POLYMER COMPOSITES, 1998, 6 (05): : 279 - 286
  • [45] High fibre volume fraction injection moulding of carbon fibre reinforced polyetheretherketone (PEEK) in order to raise mechanical properties
    Semadeni, M.
    Zerlik, H.
    Rossini, P.
    Meyer, J.
    Wintermantel, E.
    Polymers and Polymer Composites, 1998, 6 (05): : 279 - 286
  • [46] Quality Analysis of Weld-Line Defects in Carbon Fibre Reinforced Sheet Moulding Compounds by Automated Eddy Current Scanning
    Fereshteh-Saniee, Nessa
    Reynolds, Neil
    Norman, Danielle
    Qian, Connie
    Armstrong, David J. J.
    Smith, Paul
    Kupke, Richard
    Williams, Mark A. A.
    Kendall, Kenneth
    JOURNAL OF MANUFACTURING AND MATERIALS PROCESSING, 2022, 6 (06):
  • [47] A quantitative metallographic study of fibre fracture during processing and creep of a short fibre reinforced aluminium alloy
    Kausträter, G
    Skrotzki, B
    Eggeler, G
    PRAKTISCHE METALLOGRAPHIE-PRACTICAL METALLOGRAPHY, 2000, 37 (11): : 619 - 630
  • [48] Natural fibres in plastic: Compression moulding of natural-fibre-reinforced thermoset prepregs
    Medina, L
    Schiedjewski, R
    Lahm, M
    Jungmann, H
    KUNSTSTOFFE-PLAST EUROPE, 2004, 94 (03): : 92 - 94
  • [49] The control of fibre orientation in ceramic and metal composites by open-ended injection moulding
    Zhang, T
    Evans, JRG
    Bevis, MJ
    COMPOSITES SCIENCE AND TECHNOLOGY, 1996, 56 (08) : 921 - 928
  • [50] An investigation of the processability of natural fibre reinforced polymer composites on shallow and flat thin-walled parts by injection moulding process
    Azaman, M. D.
    Sapuan, S. M.
    Sulaiman, S.
    Zainudin, E. S.
    Abdan, K.
    MATERIALS & DESIGN, 2013, 50 : 451 - 456
12345