Study on fibre orientation of weld line parts during injection moulding of fibre reinforced plastic by image processing

被引：18
|
作者：
Kim, J. W. [2 ]
Kim, H. S. [3 ]
Lee, D. G. [1 ]
机构：
[1] Chosun Univ, Dept Mechatron Engn, Kwangju 501759, South Korea
[2] Iowa State Univ, Ctr NDE, Ames, IA 50011 USA
[3] Chosun Univ, Grad Sch, Dept Adv Parts & Mat Engn, Kwangju 501759, South Korea
来源：
MATERIALS RESEARCH INNOVATIONS | 2011年 / 15卷
关键词：
Injection moulding; Fibre orientation function; Fibre content ratio; Image processing; FRP; Weld line; FRP;
D O I：
10.1179/143307511X12858957674274
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In injection moulded products using fibre reinforced plastics, weld line was unavoidable due to mould shaping factors such as the position and size and number of mould gates. The weld line leads to fibre orientation perpendicular to resin flow direction, sudden reduction of the reinforcement effect and consequently degrading of the mechanical properties of moulded products. Until now, there has been no research on the measurement of fibre orientation in the weld line using image processing. Using the image processing method, the fibre orientation distribution of weld line in injection moulded products was assessed. The effects of fibre content and injection mould gate conditions on the fibre orientation were also discussed.
引用
收藏
页码：S303 / S306
页数：4
相关论文
共 50 条
  • [31] Injection Molding of Fibre Reinforced Thermoplastics: Integration of Fibre Orientation and Mechanical Properties Computations
    Miled, H.
    Silva, L.
    Coupez, T.
    Agassant, J. F.
    INTERNATIONAL POLYMER PROCESSING, 2012, 27 (05) : 547 - 556
  • [32] A Study of Fibre Attrition in the Processing of Long Fibre Reinforced Thermoplastics
    Bailey, R.
    Kraft, H.
    INTERNATIONAL POLYMER PROCESSING, 2022, 2 (02) : 94 - 101
  • [33] STUDY OF INJECTION MOULDED LONG GLASS FIBRE-REINFORCED POLYPROPYLENE AND THE EFFECT ON THE FIBRE LENGTH AND ORIENTATION DISTRIBUTION
    Parveeen, B.
    Caton-Rose, P.
    Costa, F.
    Jin, X.
    Hine, P.
    PROCEEDINGS OF PPS-29: THE 29TH INTERNATIONAL CONFERENCE OF THE POLYMER - CONFERENCE PAPERS, 2014, 1593 : 432 - 435
  • [34] Statistical analysis of fibre fracture during powder injection moulding
    German, Randall M.
    Ahmad, F.
    POWDER METALLURGY, 2006, 49 (04) : 307 - 313
  • [35] The role of fibre orientation on the electromagnetic performance of waveguides manufactured from carbon fibre reinforced plastic
    Bojovschi, Alexe
    Nicholson, K.J.
    Galehdar, A.
    Callus, P.J.
    Ghorbani, K.
    Progress In Electromagnetics Research B, 2012, (39): : 267 - 280
  • [36] Passive fibre alignment to single mode plastic waveguides fabricated by injection moulding
    Pompe, G
    Lehmacher, S
    Rudolph, S
    Kalveram, S
    Johnck, M
    Neyer, A
    POLYMER PHOTONIC DEVICES, 1998, 3281 : 37 - 46
  • [37] Study on the characteristics of glass fibre reinforced thermoplastics by transfer moulding
    1600, Elsevier Science Ltd, Oxford, Engl (32): : 1 - 4
  • [38] INJECTION MOULDING OF DISCRETE LONG-GLASS-FIBRE REINFORCED POLYPROPYLENE (LGFRP)
    Santo, Loredana
    Quadrini, Fabrizio
    Tagliaferri, Vincenzo
    Trovalusci, Federica
    PROCEEDINGS OF THE 13TH INTERNATIONAL CONFERENCE MODERN TECHNOLOGIES, QUALITY AND INNOVATION: MODTECH 2009 - NEW FACE OF TMCR, 2009, : 575 - 578
  • [39] A novel route for injection moulding of long carbon fibre-reinforced LLDPE
    Varga, Cs
    Bartha, L.
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2014, 33 (20) : 1902 - 1910
  • [40] Comparison between computed and measured fibre orientation in injection moulded parts
    A. Kech
    M. Vincent
    International Journal of Material Forming, 2008, 1 : 747 - 750
12345