Sample geometry effect on mechanical property of gold micro-cantilevers by micro-bending test

被引：4

作者：

Suzuki, Kosuke ^{[1
]}

Chang, Tso-Fu Mark ^{[1
]}

Hashigata, Ken ^{[1
]}

Asano, Keisuke ^{[1
]}

Chen, Chun-Yi ^{[1
]}

Nagoshi, Takashi ^{[2
]}

Yamane, Daisuke ^{[1
]}

Ito, Hiroyuki ^{[1
]}

Machida, Katsuyuki ^{[1
]}

Masu, Kazuya ^{[1
]}

Sone, Masato ^{[1
]}

机构：

[1] Tokyo Inst Technol, Inst Innovat Res, Yokohama, Kanagawa 2268503, Japan

[2] Natl Inst Adv Ind Sci & Technol, Tsukuba, Ibaraki 3058560, Japan

来源：

MRS COMMUNICATIONS | 2020年 / 10卷 / 03期

关键词：

TENSILE BEHAVIOR; FILMS; PLASTICITY; COPPER; NICKEL;

D O I：

10.1557/mrc.2020.38

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Sample geometry effects on mechanical strengths of gold micro-cantilevers are evaluated by a micro-bending test. Six micro-cantilevers with the same length of 50 mu m are prepared, and the width and the thickness are varied to examine individual effects on the yield stress. The yield stress increases from 428 to 519 MPa when the thickness decreases from 11.1 to 6.0 mu m. No obvious dependency is observed when varying the width. The results reveal that the thickness and the width each has a different influence on the yield stresses of micro-cantilevers evaluated by the bending test, which is the sample geometry effect.

引用

页码：434 / 438

页数：5

共 50 条

[21] Effect of current density on micro-mechanical property of electrodeposited gold film evaluated by micro-compression
Omura, Taro
Chen, Chun-Yi
Chang, Tso-Fu Mark
Yamane, Daisuke
Ito, Hiroyuki
Machida, Katsuyuki
Masu, Kazuya
Sone, Masato
Surface and Coatings Technology, 2022, 436
[22] Size-dependent pull-in instability analysis of electrically actuated packaged FG micro-cantilevers under the effect of mechanical shock
Majdi, M. A. Mokhtari Amir
Tahani, M.
Askari, Amir R.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING, 2019, 41 (02)
[23] Effect of current density on micro-mechanical property of electrodeposited gold film evaluated by micro-compression
Omura, Taro
Chen, Chun-Yi
Chang, Tso-Fu Mark
Yamane, Daisuke
Ito, Hiroyuki
Machida, Katsuyuki
Masu, Kazuya
Sone, Masato
SURFACE & COATINGS TECHNOLOGY, 2022, 436
[24] Size-dependent pull-in instability analysis of electrically actuated packaged FG micro-cantilevers under the effect of mechanical shock
M. A. Mokhtari Amir Majdi
M. Tahani
Amir R. Askari
Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2019, 41
[25] Strengthening of micro-cantilever by Au/Ti bi-layered structure evaluated by micro-bending test toward MEMS devices
Hashigata, Ken
Chang, Tso-Fu Mark
Tang, Haochun
Chen, Chun-Yi
Yamane, Daisuke
Konishi, Toshifumi
Ito, Hiroyuki
Machida, Katsuyuki
Masu, Kazuya
Sone, Masato
MICROELECTRONIC ENGINEERING, 2019, 213 : 13 - 17
[26] Mechanism of enhanced room temperature ductility of cold-rolled tungsten under micro-bending test
Wu, Xiangyu
Jimba, Yuki
Kondo, Sosuke
Yu, Hao
Ogino, Yasuyuki
Hasegawa, Akira
Kasada, Ryuta
MATERIALIA, 2024, 33
[27] Determination of the elastic properties of multi-layered foils by the four-point micro-bending test
Mendels, DA
Evanno, NMP
Cuenat, A
PHILOSOPHICAL MAGAZINE, 2005, 85 (16) : 1765 - 1782
[28] Sample size effect on micro-mechanical properties of gold electroplated with dense carbon dioxide
Tang, Haochun
Hashigata, Ken
Chang, Tso-Fu Mark
Chen, Chun-Yi
Nagoshi, Takashi
Yamane, Daisuke
Konishi, Toshifumi
Machida, Katsuyuki
Masu, Kazuya
Sone, Masato
SURFACE & COATINGS TECHNOLOGY, 2018, 350 : 1065 - 1070
[29] Numerical study on the size effect in the ultra-thin sheet's micro-bending forming process
Li, L.
Zhou, Q.
Zhou, Y. Y.
Cao, J. G.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 499 (1-2): : 32 - 35
[30] The electroplastic effect on the deformation and twinning behavior of AZ31 foils during micro-bending tests
Xiao, Xinwei
Xu, Shuai
Sui, Dashan
Zhang, Haiming
MATERIALS LETTERS, 2021, 288

← 1 2 3 4 5 →