Influence of Rotational Speed in the Friction Surfacing of Titanium Grade 1 on Ti-6Al-4V

被引：0

作者：

do Vale, Natalia Lopes ^{[1
]}

Fitseva, Viktoria ^{[2
]}

Hanke, Stefanie ^{[2
]}

Urtiga Filho, Severino Leopoldino ^{[1
]}

dos Santos, Jorge Fernandez ^{[2
]}

机构：

[1] Univ Fed Pernambuco, Programa Posgrad Engn Mecan, Recife, PE, Brazil

[2] Helmholtz Zentrum Geesthacht GmbH, Inst Mat Res, Mat Mech, Solid State Joining Proc WMP, Geesthacht, Germany

来源：

MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS | 2017年 / 20卷

关键词：

Friction Surfacing; Titanium; Coating Geometry; Microstructure; TOOL STEEL H13; PROCESS PARAMETERS; COATINGS; EVOLUTION;

D O I：

10.1590/1980-5373-MR-2016-1011

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Titanium Grade 1 was deposited on Ti-6Al-4V, 2 mm thickness, by Friction Surfacing. The process parameters were rotational speed, deposition speed and consumption rate. Only the rotational speed was varied in order to evaluate the influence of this parameter on the coatings generated. The applicability of the process has been described for a large number of materials, although the depositions of titanium alloys are still not widely studied. The objective is to investigate the effects of the rotational speed on the coatings' geometry and microstructural evolution. This investigation has shown that Titanium Grade 1 coatings can be deposited onto a Ti-6Al-4V by Friction Surfacing depending on the rotational speed. The coatings' surface homogeneity was influenced by the rotational speed, being inhomogeneous for the lowest speed. The coatings' thickness and width increased with enhancing this speed. The heat affected zone in the substrate corresponded to the complete thickness under the depositions.

引用

页码：830 / 835

页数：6

共 50 条

[31] Transformation superplasticity of cast titanium and Ti-6Al-4V
Li, Qizhen
Chen, Edward Y.
Bice, Douglas R.
Dunand, David C.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2007, 38A (01): : 44 - 53
[32] Elastic properties of the titanium alloy Ti-6Al-4V
Trofimov, E. A.
Lutfullin, R. Ya.
Kashaev, R. M.
LETTERS ON MATERIALS-PIS MA O MATERIALAKH, 2015, 5 (01): : 67 - 69
[33] Transformation Superplasticity of Cast Titanium and Ti-6Al-4V
Qizhen Li
Edward Y. Chen
Douglas R. Bice
David C. Dunand
Metallurgical and Materials Transactions A, 2007, 38 : 44 - 53
[34] Influence of electropulsing assisted on machining properties of Ti-6Al-4V titanium alloy
Shengguan Qu
Jianshuo Zhai
Pengfei Sun
Chenfeng Duan
Xiaoqiang Li
The International Journal of Advanced Manufacturing Technology, 2023, 126 : 3161 - 3174
[35] Influence of Warm Bending on the Surface Topography of Titanium Alloy Ti-6Al-4V
Dubjella, Patrick
Merklein, Marion
17TH INTERNATIONAL CONFERENCE ON SHEET METAL (SHEMET17), 2017, 183 : 23 - 30
[36] Influence of electropulsing assisted on machining properties of Ti-6Al-4V titanium alloy
Qu, Shengguan
Zhai, Jianshuo
Sun, Pengfei
Duan, Chenfeng
Li, Xiaoqiang
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2023, 126 (7-8): : 3161 - 3174
[37] Surface integrity in high speed end milling of titanium alloy Ti-6Al-4V
Daymi, A.
Boujelbene, M.
Ben Amara, A.
Bayraktar, E.
Katundi, D.
MATERIALS SCIENCE AND TECHNOLOGY, 2011, 27 (01) : 387 - 394
[38] Simulation of The High-speed Milling Temperature of Titanium Alloy Ti-6Al-4V
Huang, Xinchun
Yao, Changfeng
Zhang, Dinghua
Ren, Junxue
ADVANCED MANUFACTURING TECHNOLOGY, PTS 1-3, 2011, 314-316 : 1171 - 1175
[39] Experimental observations about the influence of the cutting conditions in high speed machining of Ti-6Al-4V titanium alloy
Castro, L.
Vieville, P.
Lipinski, P.
JOURNAL DE PHYSIQUE IV, 2006, 134 : 1273 - 1278
[40] Friction welding of conventional Ti-6Al-4V alloy with a Ti-6Al-4V based metal matrix composite reinforced by TiC
Sergey V. Prikhodko
Dmytro G. Savvakin
Pavlo E. Markovsky
Olexander O. Stasuk
James Penney
Norbert Enzinger
Michael Gaskill
Frank Deley
Welding in the World, 2021, 65 : 415 - 428

← 1 2 3 4 5 →