Study on the ductile mode cutting of LiNbO3 wafer for fabrication of SAW device

被引：0
|
作者：
Shizuka H. [1 ]
Okuda K. [1 ]
Nunobiki M. [1 ]
Li W. [1 ]
Inaoka T. [2 ]
机构：
[1] Graduate School of Engineering, University of Hyogo, Shosha 2167, Himeji, Hyogo
[2] Department of Mechanical and Systems Engineering, University of Hyogo, Shosha 2167, Himeji, Hyogo
来源：
International Journal of Abrasive Technology | 2011年 / 4卷 / 03期
关键词：
Diamond cutting; Ductile mode; Lithium niobate; Single crystal diamond; Surface acoustic wave;
D O I：
10.1504/IJAT.2011.042827
中图分类号：
学科分类号：
摘要：
This paper describes the cutting characteristics of lithium niobate, which is used for surface acoustic wave type micro pumps, regarding the formation of micro grooves by direct cutting. Since lithium niobate is a brittle material with a strong crystal orientation dependency, significant differences were observed in the characteristics of the finished surface according to different directions of cutting. The ductile mode cutting of lithium niobate was found to be feasible with cutting depths of approximately 5 μm or less. Also, results of the study show the feasibility of the formation of minute grooves through the cutting of lithium niobate, using milling with an end mill. © 2011 Inderscience Enterprises Ltd.
引用
收藏
页码：191 / 203
页数：12
相关论文
共 50 条
  • [41] ELECTROOPTICAL MODE EXTINCTION MODULATOR IN LINBO3
    PATEJ, EJ
    OPTICAL ENGINEERING, 1994, 33 (05) : 1717 - 1720
  • [42] Large-Range Spurious Mode Elimination for Wideband SAW Filters on LiNbO3/SiO2/Si. Platform by LiNbO3 Cut Angle Modulation
    Xu, Huiping
    Fu, Sulei
    Shen, Junyao
    Lu, Zengtian
    Su, Rongxuan
    Wang, Rui
    Song, Cheng
    Zeng, Fei
    Wang, Weibiao
    Pan, Feng
    IEEE TRANSACTIONS ON ULTRASONICS FERROELECTRICS AND FREQUENCY CONTROL, 2022, 69 (11) : 3117 - 3125
  • [43] Fabrication and characterization of 5-mm-thick periodically poled MgO:LiNbO3 device
    Ishizuki, H
    Taira, T
    2005 Conference on Lasers & Electro-Optics (CLEO), Vols 1-3, 2005, : 2108 - 2110
  • [44] The effect of the cutting edge radius on a machined surface in the nanoscale ductile mode cutting of silicon wafer
    Arefin, S.
    Li, X. P.
    Cai, M. B.
    Rahman, M.
    Liu, K.
    Tay, A.
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2007, 221 (02) : 213 - 220
  • [45] FABRICATION AND CHARACTERISTICS OF OPTICAL-WAVEGUIDES ON LINBO3
    ARMENISE, MN
    CANALI, C
    DESARIO, M
    ZANONI, E
    MATERIALS CHEMISTRY AND PHYSICS, 1983, 9 (1-3) : 267 - 284
  • [46] Fabrication of Bragg Gratings on LiNbO3 optical waveguides
    Ulliac, G.
    Lecestre, A.
    Guichardaz, B.
    Dandah, J.
    Baida, F. I.
    Bernal, M-P
    Courjal, N.
    MICROELECTRONIC ENGINEERING, 2012, 97 : 185 - 188
  • [47] New type double mode saw resonator filters on 64 degrees Y-X LiNbO3
    Roh, YR
    Kim, HB
    Lee, YJ
    Lee, MH
    Kim, KB
    Kim, KH
    PROCEEDINGS OF THE 1996 IEEE INTERNATIONAL FREQUENCY CONTROL SYMPOSIUM (50TH ANNIVERSARY), 1996, : 194 - 198
  • [48] Advanced Substrate Material for SAW Devices Combining LiNbO3 and Langasite
    Naumenko, Natalya F.
    IEEE TRANSACTIONS ON ULTRASONICS FERROELECTRICS AND FREQUENCY CONTROL, 2020, 67 (09) : 1909 - 1915
  • [49] Quantum 1/f effect in ferroelectric LiNbO3 saw resonators
    Handel, PH
    Tsai, CS
    PROCEEDINGS OF THE 2000 IEEE/EIA INTERNATIONAL FREQUENCY CONTROL SYMPOSIUM & EXHIBITION, 2000, : 561 - 564
  • [50] Investigation of the SAW property change for surface processed LiNbO3 crystal
    Lin, B
    Zhang, XR
    Lu, XM
    Zhang, D
    Review of Progress in Quantitative Nondestructive Evaluation, Vols 24A and 24B, 2005, 760 : 235 - 242
12345