Study on the ductile mode cutting of LiNbO3 wafer for fabrication of SAW device

被引：0
|
作者：
Shizuka H. [1 ]
Okuda K. [1 ]
Nunobiki M. [1 ]
Li W. [1 ]
Inaoka T. [2 ]
机构：
[1] Graduate School of Engineering, University of Hyogo, Shosha 2167, Himeji, Hyogo
[2] Department of Mechanical and Systems Engineering, University of Hyogo, Shosha 2167, Himeji, Hyogo
来源：
International Journal of Abrasive Technology | 2011年 / 4卷 / 03期
关键词：
Diamond cutting; Ductile mode; Lithium niobate; Single crystal diamond; Surface acoustic wave;
D O I：
10.1504/IJAT.2011.042827
中图分类号：
学科分类号：
摘要：
This paper describes the cutting characteristics of lithium niobate, which is used for surface acoustic wave type micro pumps, regarding the formation of micro grooves by direct cutting. Since lithium niobate is a brittle material with a strong crystal orientation dependency, significant differences were observed in the characteristics of the finished surface according to different directions of cutting. The ductile mode cutting of lithium niobate was found to be feasible with cutting depths of approximately 5 μm or less. Also, results of the study show the feasibility of the formation of minute grooves through the cutting of lithium niobate, using milling with an end mill. © 2011 Inderscience Enterprises Ltd.
引用
收藏
页码：191 / 203
页数：12
相关论文
共 50 条
  • [21] Analysis of guided SAW in channel waveguides on LiNbO3
    Chen, M
    Tang, TT
    CHINESE JOURNAL OF ELECTRONICS, 2004, 13 (02): : 219 - 221
  • [22] OBSERVATION OF BIFURCATIONS AND CHAOS IN SAW ON SUBSTRATE OF LINBO3
    ZHOU, JP
    ZHANG, SY
    WEI, RJ
    IEEE TRANSACTIONS ON ULTRASONICS FERROELECTRICS AND FREQUENCY CONTROL, 1986, 33 (01) : 79 - 79
  • [23] PRECISE MEASUREMENT OF SAW PROPAGATION VELOCITY ON LINBO3
    TEMMYO, J
    KOTAKA, I
    INAMURA, T
    YOSHIKAWA, S
    IEEE TRANSACTIONS ON SONICS AND ULTRASONICS, 1980, 27 (04): : 218 - 219
  • [24] SUPPRESSION OF HIGHER HARMONIC GENERATIONS OF SAW IN LINBO3
    LEE, J
    SINGH, MP
    ZUCKER, J
    APPLIED PHYSICS LETTERS, 1980, 36 (11) : 896 - 898
  • [25] Temperature coefficient of SAW device on SiO2/proton exchanged LiNbO3 substrate
    Cheng, CC
    Kao, KS
    Chen, PC
    Chung, CJ
    FERROELECTRICS, 2004, 304 : 973 - 975
  • [26] FEM Modeling and Simulation of a Layered SAW device Based on ZnO/128° YX LiNbO3
    Salim, Zaid. T.
    Hashim, U.
    Arshad, M. K. Md.
    2016 IEEE INTERNATIONAL CONFERENCE ON SEMICONDUCTOR ELECTRONICS (ICSE) PROCEEDINGS, 2016, : 5 - 8
  • [27] Calculation and optical measurement of SAW diffraction pattern of slanted finger SAW filters on YZ LiNbO3 and 128YX LiNbO3
    Yatsuda, H
    Kamiseki, S
    Chiba, T
    2001 IEEE ULTRASONICS SYMPOSIUM PROCEEDINGS, VOLS 1 AND 2, 2001, : 13 - 17
  • [28] The study of ZnO/XY LiNbO3 layered saw devices for sensing applications
    Ippolito, SJ
    Kalantar-Zadeh, K
    Wlodarski, W
    Matthews, GI
    PROCEEDINGS OF THE IEEE SENSORS 2003, VOLS 1 AND 2, 2003, : 539 - 542
  • [29] Etching study of ferroelectric microdomains in LiNbO3 and MgO:LiNbO3
    Holstein, WL
    JOURNAL OF CRYSTAL GROWTH, 1997, 171 (3-4) : 477 - 484
  • [30] FABRICATION OF LINBO3 WAVEGUIDES BY TITANIUM DIFFUSION
    SUGII, K
    FUKUMA, M
    NODA, J
    IWASAKI, H
    FERROELECTRICS, 1978, 19 (3-4) : 168 - 168
12345