Characterization of Polylactic Acid Parts Produced Using the Fused Deposition Modelling

被引：0
|
作者：
E. Zīle
D. Zeleniakiene
A. Aniskevich
机构：
[1] Institute for Mechanics of Materials,Department of Mechanical Engineering
[2] University of Latvia,undefined
[3] Kaunas University of Technology,undefined
来源：
Mechanics of Composite Materials | 2022年 / 58卷
关键词：
fused deposition modelling; laminate; voids; fiber;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
This work is devoted to studying the mechanical behavior of a polylactic acid (PLA) material produced by the fused deposition modelling. The influence of mesostructure on their macro-scale mechanical properties is characterized by porosity. The dependence of its longitudinal and transverse properties on the porosity is found experimentally. It is shown that, due to the crystallization after melting and extrusion, the properties of a single PLA fiber increase in time. The results obtained show that the classical lamination theory and the Tsai–Hill failure criterion can predict the modulus and strength of PLA printed materials.
引用
收藏
页码：169 / 180
页数：11
相关论文
共 50 条
  • [41] Characterization of short fiber-reinforced polylactic acid composites produced with Fused Filament Fabrication (FFF)
    Toth, Csenge
    Kovacs, Krisztian Norbert
    12TH HUNGARIAN CONFERENCE ON MATERIALS SCIENCE (HMSC12), 2020, 903
  • [42] Mechanical characterization of parts processed via fused deposition
    Bertoldi, M
    Yardimci, MA
    Pistor, CM
    Güçeri, SI
    Sala, G
    SOLID FREEFORM FABRICATION PROCEEDINGS, AUGUST, 1998, 1998, : 557 - 565
  • [43] Enhanced mechanical properties of plasticized polylactic acid filament for fused deposition modelling: Effect of in situ heat treatment
    Rafie, M. A. F.
    Marsilla, K. I. Ku
    Hamid, Z. A. A.
    Rusli, A.
    Abdullah, M. K.
    PROGRESS IN RUBBER PLASTICS AND RECYCLING TECHNOLOGY, 2020, 36 (02) : 131 - 142
  • [44] Production and characterization of bamboo and flax fiber reinforced polylactic acid filaments for fused deposition modeling (FDM)
    Depuydt, Delphine
    Balthazar, Michiel
    Hendrickx, Kevin
    Six, Wim
    Ferraris, Eleonora
    Desplentere, Frederik
    Ivens, Jan
    Van Vuure, Aart W.
    POLYMER COMPOSITES, 2019, 40 (05) : 1951 - 1963
  • [45] Preparation of Thermoplastic Polyurethane Parts Reinforced with in Situ Polylactic Acid Microfibers during Fused Deposition Modeling: The Influences of Deposition-Induced Effects
    Leng, Jie
    Wu, Junjie
    Zhang, Jie
    INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH, 2019, 58 (47) : 21476 - 21484
  • [46] Thermomechanical Analysis and Numerical Simulations of Fused Filament Fabricated Polylactic Acid Parts
    Bute, Irina
    Tarasovs, Sergejs
    Sevcenko, Jevgenijs
    Aniskevich, Andrey
    MATERIALS SCIENCE-MEDZIAGOTYRA, 2024, 30 (02): : 217 - 225
  • [47] Mechanical Properties of Polylactic Acid/Chitosan Composites by Fused Deposition Modeling
    Bera, Tanusree
    Vincent, Sumi
    Mohanty, Smita
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2024,
  • [48] Mechanical properties of thermoplastic parts produced by fused deposition modeling: a review
    Bakir, Ali Alperen
    Atik, Resul
    Ozerinc, Sezer
    RAPID PROTOTYPING JOURNAL, 2021, 27 (03) : 537 - 561
  • [49] Investigation of the Influence of Fused Deposition Modeling 3D Printing Process Parameters on Tensile Properties of Polylactic Acid Parts Using the Taguchi Method
    Megersa, Getu Koro
    Sitek, Wojciech
    Nowak, Agnieszka J.
    Tomasic, Neven
    MATERIALS, 2024, 17 (23)
  • [50] INFLUENCE OF PROCESS PARAMETERS ON DIMENSIONAL ACCURACY OF PARTS MANUFACTURED USING FUSED DEPOSITION MODELLING TECHNOLOGY
    Gorski, Filip
    Kuczko, Wieslaw
    Wichniarek, Radoslaw
    ADVANCES IN SCIENCE AND TECHNOLOGY-RESEARCH JOURNAL, 2013, 7 (19): : 27 - 35
12345