Analysis of the creep response of the AE44 magnesium alloy between 100 and 150°C

被引:0
|
作者
Spigarelli, S. [1 ]
Evangelista, E. [1 ]
Cabibbo, M. [1 ]
El Mehtedi, M. [1 ]
机构
[1] Unic Politecn Marche, Dipartimento Meccan, I-60131 Ancona, Italy
来源
关键词
creep; minimum creep rate; composite model; rare Earths;
D O I
暂无
中图分类号
TF [冶金工业];
学科分类号
0806 ;
摘要
The creep response of the AE44 magnesium alloy was investigated by means of constant load creep tests carried out between 100 and 150 degrees C. The minimum creep rate dependence on applied stress was described by a conventional power law, with a stress exponent n larger than 30 at the highest temperature. The minimum creep rate in the low stress regime was thus about two orders of magnitude lower in AE44 than in AM50. This large difference in creep response has been attributed to the presence and evolution of rare earths (RE) intermetallic phases mainly distributed in the grain boundary zone in form of an almost continuous network of dispersoids, that were observed by means of optical and scanning electron microscopy.
引用
收藏
页码:401 / +
页数:2
相关论文
共 50 条
  • [41] Quantitative fractographic analysis of variability in the tensile ductility of high-pressure die-cast AE44 Mg-alloy
    Lee, S. G.
    Patel, G. R.
    Gokhale, A. M.
    Sreeranganathan, A.
    Horstemeyer, M. F.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2006, 427 (1-2): : 255 - 262
  • [42] The Ductility Variation of High-Pressure Die-Cast AE44 Alloy: The Role of Inhomogeneous Microstructure
    Xia, Yatong
    Zheng, Jiang
    Chen, Juan
    Zhang, Yongfa
    Shi, Rong
    Zhou, Hao
    Zhou, Zheng
    Yin, Dongdi
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2021, 52 (06): : 2274 - 2286
  • [43] Microstructural development in tension and compression creep of magnesium alloy AE42
    Dieringa, H
    Bowles, A
    Hort, N
    Kainer, KU
    MATERIALS STRUCTURE & MICROMECHANICS OF FRACTURE IV, 2005, 482 : 271 - 274
  • [44] Creep Behaviour of AE42 Magnesium Alloy and Its Composites Using Impression Creep Technique
    Mondal, A. K.
    Kumar, S.
    THERMEC 2009, PTS 1-4, 2010, 638-642 : 1552 - 1557
  • [45] Development of high thermal conductivity, enhanced strength and cost-effective die-cast Mg alloy compared with AE44 alloy
    Feng, Lingyun
    Dong, Xixi
    Xia, Mingxu
    Zhu, Xiangzhen
    Ji, Gang
    Yang, Hailin
    Wang, Bin
    Nyberg, Eric A.
    Ji, Shouxun
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2023, 22 : 2955 - 2966
  • [46] Al-RE Intermetallic Phase Stability and Effects on Corrosion Behavior in Cold-Chamber HPDC AE44 Alloy
    Jiao, Yufeng
    Zhang, Jinghuai
    He, Lili
    Zhang, Milin
    Jiang, Fengchun
    Wang, Wei
    Han, Liming
    Xu, Longjiang
    Wu, Ruizhi
    ADVANCED ENGINEERING MATERIALS, 2016, 18 (01) : 148 - 155
  • [47] ANALYSIS OF CREEP CURVES FOR A MAGNESIUM - ZIRCONIUM ALLOY
    WOODFORD, DA
    JOURNAL OF THE INSTITUTE OF METALS, 1968, 96 : 371 - &
  • [48] Characteristics and formation mechanisms of defect bands in vacuum-assisted high-pressure die casting AE44 alloy
    Hou, Ying-ying
    Wu, Meng-wu
    Tian, Bing-hui
    LI, Xiao-bo
    Xiong, Shou-mei
    TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2022, 32 (06) : 1852 - 1865
  • [49] Threshold stress during tensile and compressive creep in AE42 magnesium alloy
    Dieringa, Hajo
    Hort, Norbert
    Kainer, Karl Ulrich
    MAGNESIUM TECHNOLOGY 2007, 2007, : 395 - +
  • [50] Microstructure and creep behavior in AE42 magnesium die-casting alloy
    Powell, BR
    Rezhets, V
    Balogh, MP
    Waldo, RA
    JOM-JOURNAL OF THE MINERALS METALS & MATERIALS SOCIETY, 2002, 54 (08): : 34 - 38