Fabrication of ultra-fine TiO2 ceramics by a high-frequency induction heated sintering method

被引：0
|
作者：
Kim, Hwan-Cheol [1 ]
Park, Hyun-Kuk [1 ]
Shon, In-Jin [1 ]
Ko, In-Yong [1 ]
机构：
[1] Chonbuk Natl Univ, Res Ctr Adv Mat Dev, Jeonju 560756, Jeonbuk, South Korea
来源：
JOURNAL OF CERAMIC PROCESSING RESEARCH | 2006年 / 7卷 / 04期
关键词：
rapid sintering; high-frequency induction heated sintering; TiO2; hardness; fracture toughness;
D O I：
暂无
中图分类号：
TQ174 [陶瓷工业]; TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
High-frequency induction heated sintering (HFIHS) is utilized to consolidate ultra-fine rutile TiO2 ceramics. Densification to near theoretical density in a relatively short time can be accomplished using this method. Samples of TiO2 with a relative density of up to 98% and an average grain size of about 160 nm could be obtained by sintering at 830 degrees C for 5 minutes under a pressure of 100 MPa. The influence of sintering temperature and mechanical pressure on the final density and grain size of the sintered products was investigated. The sintered materials had fracture toughness and hardness values of 12.8 GPa and 3.1 MPa center dot ml(1/2), respectively.
引用
收藏
页码：327 / 331
页数：5
相关论文
共 50 条
  • [11] Fabrication of Ultra-fine Grain Tungsten by Combining Spark Plasma Sintering with Resistance Sintering under Ultra High Pressure
    Ma Yao
    Zhou Zhangjian
    Tan Jun
    Li Ming
    RARE METAL MATERIALS AND ENGINEERING, 2011, 40 (01) : 4 - 8
  • [12] Fabrication and characterization of ultra-fine grained tungsten by resistance sintering under ultra-high pressure
    Zhou, Zhangjian
    Ma, Yao
    Du, Juan
    Linke, Jochen
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 505 (1-2): : 131 - 135
  • [13] Synthesis of ultra-fine TiO2 powder using thermal plasma
    Oh, SM
    Gong, JG
    Park, DW
    JOURNAL OF CHEMICAL ENGINEERING OF JAPAN, 2001, 34 (02) : 283 - 286
  • [14] Fabrication and characterization of a Ni-YSZ anode support using high-frequency induction heated sintering (HFIHS)
    Yoo, Jong-Yeol
    Shon, In-Jin
    Choi, Byung-Hyun
    Lee, Ki-Tae
    CERAMICS INTERNATIONAL, 2011, 37 (07) : 2569 - 2574
  • [15] High-frequency induction heating sintering of ultra-fine Al2O3-(ZrO2+X%mol Y2O3) bioceramics
    Kim, S. W.
    Khalil, K. A.
    Ogi, K.
    ADVANCED MATERIALS AND PROCESSING IV, 2007, 29-30 : 235 - +
  • [16] Effect of milling on properties and consolidation of AlN by high-frequency induction heated sintering
    In-Jin Shon
    Hanjung Kwon
    Hyun-Su Oh
    Electronic Materials Letters, 2014, 10 : 337 - 343
  • [17] Consolidation of binderless nanostructured titanium carbide by high-frequency induction heated sintering
    Shon, In-Jin
    Kim, Byung-Ryang
    Doh, Jung-Mann
    Yoon, Jin-Kook
    CERAMICS INTERNATIONAL, 2010, 36 (06) : 1797 - 1803
  • [18] Effect of Milling on Properties and Consolidation of AlN by High-Frequency Induction Heated Sintering
    Shon, In-Jin
    Kwon, Hanjung
    Oh, Hyun-Su
    ELECTRONIC MATERIALS LETTERS, 2014, 10 (02) : 337 - 343
  • [19] Preparation of high-purity TiO2 ultra-fine powder used in electronic ceramics by TiCl4 direct hydrolysis
    Zhou, D.L.
    Li, D.C.
    Quan, X.J.
    Wang, R.S.
    Sichuan Daxue Xuebao (Gongcheng Kexue Ban)/Journal of Sichuan University (Engineering Science Edition), 2001, 33 (02):
  • [20] Synthesis of ultra-fine TiO2 powders by controlled hydrolysis of titanium tetrabutoxide
    Potdar, HS
    Deshpande, SB
    Mayadevi, S
    Joy, PA
    Date, SK
    INDIAN JOURNAL OF CHEMISTRY SECTION A-INORGANIC BIO-INORGANIC PHYSICAL THEORETICAL & ANALYTICAL CHEMISTRY, 1999, 38 (05): : 468 - 472
12345