Dissolution of the θ′ precipitates in an Al-1.7at. % Cu alloy deformed by equal-channel angular pressing

被引：0
|
作者：
Murayama, M [1 ]
Hono, K [1 ]
Horita, Z [1 ]
机构：
[1] Natl Res Inst Met, Tsukuba, Ibaraki 3050047, Japan
来源：
ULTRAFINE GRAINED MATERIALS | 2000年
关键词：
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The microstructural evolution during the equal channel angular (ECA) pressing process of an alpha+ theta' two-phase Al-1.7at.%Cu alloy has been studied by transmission electron microscopy (TEM) and energy-filtered transmission electron microscopy (EF-TEM). The theta' precipitates are fragmented into fine particles after a few passes of ECA perssing. The theta' precipitates are almost completely dissolved after 8 passes of the ECA pressing, and nearly single phase cc with a fine grain size of approximately 500 nm is obtained. The dissolution process of the theta' precipitates and the distribution of Cu atoms during the severe plastic deformation have been observed by energy-filtered TEM.
引用
收藏
页码：145 / 153
页数：9
相关论文
共 50 条
  • [31] Influence of Processing Severity During Equal-Channel Angular Pressing on the Microstructure of an Al-Zn-Mg-Cu Alloy
    Carmen M. Cepeda-Jiménez
    Juan M. García-Infanta
    Edgar F. Rauch
    Jean J. Blandin
    Oscar A. Ruano
    Fernando Carreño
    Metallurgical and Materials Transactions A, 2012, 43 : 4224 - 4236
  • [32] Effect of equal-channel angular pressing and aging on the microstructure and mechanical properties of an Al-Cu-Mg-Si alloy
    M. R. Gazizov
    A. V. Dubina
    D. A. Zhemchuzhnikova
    R. O. Kaibyshev
    The Physics of Metals and Metallography, 2015, 116 : 718 - 729
  • [33] The development of hardness homogeneity in a Cu-Zr alloy processed by equal-channel angular pressing
    Wongsa-Ngam, Jittraporn
    Kawasaki, Megumi
    Langdon, Terence G.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 556 : 526 - 532
  • [34] Development of ultrafine-grained microstructure in Al-Cu-Mg alloy through equal-channel angular pressing
    Anuhya, Danam Sai
    Gupta, Ashutosh
    Nayan, Niraj
    Murty, S. V. S. Narayana
    Manna, R.
    Sastry, G. V. S.
    6TH INTERNATIONAL CONFERENCE ON NANOMATERIALS BY SEVERE PLASTIC DEFORMATION (NANOSPD6), 2014, 63
  • [35] Wear behavior of an aluminum alloy processed by equal-channel angular pressing
    Wang, Chuan Ting
    Gao, Nong
    Wood, Robert J. K.
    Langdon, Terence G.
    JOURNAL OF MATERIALS SCIENCE, 2011, 46 (01) : 123 - 130
  • [36] Improvement in Hardness of Al-Ag-Cu Alloy via Equal-Channel Angular Pressing and Subsequent Aging Processes
    Salazar-Munoz, V. E.
    Garcia-Rocha, J.
    Elias, Ivonne Kado-Mercado
    Gutierrez-Castaneda, E. J.
    Urbano-Pena, M. A.
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2025,
  • [37] Influence of Processing Severity During Equal-Channel Angular Pressing on the Microstructure of an Al-Zn-Mg-Cu Alloy
    Cepeda-Jimenez, Carmen M.
    Garcia-Infanta, Juan M.
    Rauch, Edgar F.
    Blandin, Jean J.
    Ruano, Oscar A.
    Carreno, Fernando
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2012, 43A (11): : 4224 - 4236
  • [38] Lamellae deformation and structural evolution in an Al-33%Cu eutectic alloy during equal-channel angular pressing
    Jingtao Wang
    Suk-Bong Kang
    Hyung-Wook Kim
    Zenji Horita
    Journal of Materials Science, 2002, 37 : 5223 - 5227
  • [39] Fatigue properties of 8090 Al-Li alloy processed by equal-channel angular pressing
    Liu, SM
    Wang, ZG
    SCRIPTA MATERIALIA, 2003, 48 (10) : 1421 - 1426
  • [40] Superplasticity in an Al-Mg-Zr-Sc alloy produced by equal-channel angular pressing
    Turba, K.
    Malek, P.
    Cieslar, M.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 462 (1-2): : 91 - 94
12345