The effect of crack insertion for FDM printed PLA materials on Mode I and Mode II fracture toughness

被引：31

作者：

Valean, Cristina ^{[1
]}

Marsavina, Liviu ^{[1
]}

Marghitas, Mihai ^{[1
]}

Linul, Emanoil ^{[1
]}

Razavi, Nima ^{[2
]}

Berto, Filippo ^{[2
]}

Brighenti, Roberto ^{[3
]}

机构：

[1] Univ Politehn Timisoara, 1 Mihai Viteazu Ave, Timisoara 300222, Romania

[2] Norwegian Univ Sci & Technol NTNU, Richard Birkelands Vei 2b, N-7491 Trondheim, Norway

[3] Univ Parma, Viale Sci 181-A, I-43124 Parma, Italy

来源：

1ST VIRTUAL EUROPEAN CONFERENCE ON FRACTURE - VECF1 | 2020年 / 28卷

关键词：

Additive Manufacturing; Fused deposition modeling; PLA; mode I; mode II; fracture toughness;

D O I：

10.1016/j.prostr.2020.11.128

中图分类号：

TU [建筑科学];

学科分类号：

0813 ;

摘要：

The paper presents mode I and II fracture toughness results for polylactic acid material obtained via fused deposition modeling. The tests were performed using Single Edge Notch Bend specimens loaded in four point bending: symmetric for mode I, asymmetric for mode II, respectively. The notch was inserted by 3D printing, and by milling, respectively. Fracture toughness values measured for the specimens with 3D printed notch resulted to be higher than those obtained by milling. The effect of notch insertion is more evident in mode I while it is less important for mode II. (C) 2020 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (https://creativecommons.org/licenses/by-nc-nd/4.0) Peer-review under responsibility of the European Structural Integrity Society (ESIS) ExCo

引用

页码：1134 / 1139

页数：6

共 50 条

[21] Experimental observations on the effect of thermal treatment on the crack speed and mode I and II fracture toughness in brittle and ductile rocks
Alneasan, Mahmoud
Alzo'ubi, Abdel Kareem
Behnia, Mahmoud
Mughieda, Omer
THEORETICAL AND APPLIED FRACTURE MECHANICS, 2022, 121
[22] Determination of mode I and mode II fracture toughness of walnut and cherry in TR and RT crack propagation system by the Arcan test
Murata, Koji
Bachtiar, Erik Valentine
Niemz, Peter
HOLZFORSCHUNG, 2017, 71 (12) : 985 - 990
[23] Mixed Mode I/II fracture toughness of bonded joints
Pirondi, A
Nicoletto, G
INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES, 2002, 22 (02) : 109 - 117
[24] Fracture toughness for mixed mode I/II of epoxy resin
Araki, W
Nemoto, K
Adachi, T
Yamaji, A
ACTA MATERIALIA, 2005, 53 (03) : 869 - 875
[25] Fracture toughness of bulk adhesives in mode I and mode III and curing effect
Chen, Z.
Adams, R. D.
da Silva, Lucas F. M.
INTERNATIONAL JOURNAL OF FRACTURE, 2011, 167 (02) : 221 - 234
[26] Fracture toughness of bulk adhesives in mode I and mode III and curing effect
Z. Chen
R. D. Adams
Lucas F. M. da Silva
International Journal of Fracture, 2011, 167 : 221 - 234
[27] On the combined mode I mode II fracture toughness of a fiber reinforced polymer composite
Manoharan, M
Xiao, H
INTERNATIONAL JOURNAL OF FRACTURE, 1997, 88 (01) : L3 - L7
[28] Fracture toughness of aged dental composites in combined mode I and mode II loading
Scherrer, SS
Botsis, J
Studer, M
Pini, M
Wiskott, HWA
Belser, UC
JOURNAL OF BIOMEDICAL MATERIALS RESEARCH, 2000, 53 (04): : 362 - 370
[29] Fracture toughness in SPCC/CFRP hybrid laminates: Mode I and mode II perspectives
Nugraha, Ariyana Dwiputra
Hakim, Muhammad Luthfi
Pramana, Ari
Triawan, Farid
Handayani, Murni
Rahmayanti, Yosephin Dewiani
Muflikhun, Muhammad Akhsin
RESULTS IN ENGINEERING, 2024, 24
[30] Interlaminar fracture toughness of CFRP in mode I and mode II determined by Raman spectroscopy
Miyagawa, H
Sato, C
Ikegami, K
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2001, 32 (3-4) : 477 - 486

← 1 2 3 4 5 →