Optimal Configuration Design of MRI REBCO Magnet Taking into Account Superconducting Layer

被引：0

作者：

Noguchi, So ^{[1
]}

Miyazaki, Hiroshi ^{[2
]}

Tosaka, Taizo ^{[2
]}

Nomura, Shunji ^{[2
]}

Kurusu, Tsutomu ^{[2
]}

Ueda, Hiroshi ^{[3
]}

Ishiyama, Atsushi ^{[4
]}

Urayama, Shinichi ^{[5
]}

Fukuyama, Hidenao ^{[5
]}

机构：

[1] Hokkaido Univ, Grad Sch Informat Sci & Technol, Sapporo, Hokkaido, Japan

[2] Toshiba Co Ltd, Yokohama, Kanagawa, Japan

[3] Okayama Univ, Grad Sch Nat Sci & Technol, Okayama, Japan

[4] Waseda Univ, Sch Adv Sci & Engn, Tokyo, Japan

[5] Kyoto Univ, Grad Sch Med, Kyoto, Japan

来源：

2016 IEEE CONFERENCE ON ELECTROMAGNETIC FIELD COMPUTATION (CEFC) | 2016年

关键词：

Field homogeneity; MRI; optimal design; REBCO coated conductor;

D O I：

暂无

中图分类号：

TP301 [理论、方法];

学科分类号：

081202 ;

摘要：

The development of ultra-high-field (similar to 10 T magnetic resonance imaging (MRI) device is underway. It is, therefore, required to achieve the extremely high field homogeneity at a magnet design stage, where the field homogeneity is evaluated using the Legendre polynomials. Commonly, it is supposed that the current uniformly flows on the cross section of coils. However, for REBCO magnet, the no-current-flowing region has to be taken into account, such as a copper stabilizer. In addition, the REBCO layer inside REBCO tape is very thin, 1 - 2 mu m, so the current-flowing region is 1/100 of the REBCO tape area. Therefore, it is necessary to consider that the current flows only in the REBCO layer, for accurate evaluation of field homogeneity.

引用

页数：1

共 50 条

[21] OPTIMAL-DESIGN OF A SUPERCONDUCTING MHD SADDLE MAGNET
LIA, GMA
MONTANARI, I
RIBANI, PL
IEEE TRANSACTIONS ON MAGNETICS, 1992, 28 (01) : 466 - 469
[22] Three-dimensional optimal shape design of magnetic pole in permanent magnet assembly for MRI taking account of Eddy currents due to gradient coil field
Yao, YY
Koh, CS
Xie, DX
IEEE TRANSACTIONS ON MAGNETICS, 2004, 40 (02) : 1164 - 1167
[23] Design of a REBCO Insert Coil for a Cryogen-Free 25-T Superconducting Magnet
Miyazaki, H.
Iwai, S.
Takahashi, M.
Tosaka, T.
Tasaki, K.
Hanai, S.
Ioka, S.
Watanabe, K.
Awaji, S.
Oguro, H.
IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY, 2015, 25 (03)
[24] Design, Fabrication, and Test of a 16 T 100 mm all-REBCO Superconducting Magnet
Hu, Shuai
Liu, Huajun
Liu, Fang
Wang, Zhaoran
Hong, Wenzhe
Gao, Shuowei
Guo, Liang
Ma, Hongjun
Xue, Shenquan
Zhang, Shuqing
Yang, Dongshen
Shao, Liangjun
Qu, Timing
Zhu, Jiamin
Zhang, Xintao
IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY, 2025, 35 (05)
[25] Design of a 20 T Class REBCO Insert in a 15 T Low Temperature Superconducting Magnet
Shao, Liangjun
Zhang, Xintao
Yan, Yufan
Wang, Haoyuan
Liu, Huajun
Qu, Timing
ELECTRONICS, 2021, 10 (14)
[26] Basic Design of REBCO Insert Coil of 33 T Cryogen-Free Superconducting Magnet
Uto, T.
Tosaka, T.
Shitaka, T.
Nezuka, H.
Hanai, S.
Takewa, H.
Inagaki, J.
Ioka, S.
Badel, A.
Takahashi, K.
Zampa, A.
Okada, T.
Tsuchiya, Y.
Awaji, S.
IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY, 2025, 35 (05)
[27] Quench Protection Design of a 1.5 T Superconducting MRI Magnet
Li, Yi
Wang, Qiuliang
Chen, Shunzhong
Liu, Feng
Hu, Xinning
Yan, Luguang
IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY, 2012, 22 (03)
[28] Design optimization of superconducting MRI magnet with polygonal iron yoke
Li, Qingfu
Yang, Xin
Liu, Yunsong
Hsi-An Chiao Tung Ta Hsueh/Journal of Xi'an Jiaotong University, 1996, 30 (11): : 14 - 19
[29] Design and Optimization of Superconducting MRI Magnet Systems With Magnetic Materials
Tadic, Tony
Fallone, B. Gino
IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY, 2012, 22 (02)
[30] Evaluation of influence of external magnetic disturbance on superconducting magnet taking conservation of linkage flux into account
Takechi, Moriaki
Kuroda, Sigenori
Electrical Engineering in Japan (English translation of Denki Gakkai Ronbunshi), 1996, 116 (02): : 112 - 123

← 1 2 3 4 5 →