Characteristic of cavity growth of superplastic al 7475 alloy containing a small amount of liquid

被引：0

作者：

Iwasaki, H ^{[1
]}

Mori, T ^{[1
]}

Mabuchi, M ^{[1
]}

Higashi, K ^{[1
]}

机构：

[1] Himeji Inst Technol, Dept Mat Sci & Engn, Himeji, Hyogo 6712201, Japan

来源：

PRICM 4: FORTH PACIFIC RIM INTERNATIONAL CONFERENCE ON ADVANCED MATERIALS AND PROCESSING, VOLS I AND II | 2001年

关键词：

cavity growth; superplasticity; 7475 alminum alloy; liquidp hase;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The change in an artificial hole during superplastic flow was measured at 773 and 806 K in AA 7475 Al alloy to investigate the effect of a small amount of liquid on plastic cavity growth during grain boundary sliding, where 773 K was lower than the incipient partial melting temperature and 806 K was slightly above the incipient partial melting temperature. The cavity growth rate at 806 K was lower than that at 773 K, indicating that cavity growth is suppressed by the presence of a small amount of liquid. The low cavity growth rate due to a small amount of liquid is suggested to be attributed to the change in the. stress state at the liquid boundaries.

引用

页码：1995 / 1997

页数：3

共 50 条

[31] The thickness of liquid phase during superplastic deformation in the vicinity of solidus temperature for a 7475 aluminum alloy
Takayama, Y
Tozawa, T
Kato, H
TOWARDS INNOVATION IN SUPERPLASTICITY II, 1999, 304-3 : 291 - 296
[32] An investigation of cavity growth in a superplastic aluminum alloy processed by ECAP
Kawasaki, M
Xu, C
Langdon, TG
ACTA MATERIALIA, 2005, 53 (20) : 5353 - 5364
[33] Cavity growth in a superplastic Al-Mg alloy: II. An improved plasticity based model
Bae, DH
Ghosh, AK
ACTA MATERIALIA, 2002, 50 (05) : 1011 - 1029
[34] Cavity formation and growth in a superplastic alumina containing zirconia particles
Hiraga, K
Nakano, K
Suzuki, TS
Sakka, Y
SUPERPLASTICITY IN ADVANCED MATERIALS, ICSAM-2000, 2001, 357-3 : 193 - 198
[35] Cavity growth during superplastic flow in an Al-Mg alloy: I. Experimental study
Bae, DH
Ghosh, AK
ACTA MATERIALIA, 2002, 50 (05) : 993 - 1009
[36] Superplastic Behavior at Lower Temperatures of High-Strength Ultrafine-Grained Al Alloy 7475
Bobruk, Elena V.
Murashkin, Maxim Y.
Kazykhanov, Vil U.
Valiev, Ruslan Z.
ADVANCED ENGINEERING MATERIALS, 2019, 21 (01)
[37] Cavity of Al-Cu-Mg alloy during superplastic deformation
Wang, M.
Guo, H. Z.
Liu, Y. J.
SUPERPLASTICITY IN ADVANCED MATERIALS, 2007, 551-552 : 645 - +
[38] An investigation of cavity growth rate in superplastic Al and Mg alloys
Mabuchi, M
Chino, Y
Iwasaki, H
PRICM 5: THE FIFTH PACIFIC RIM INTERNATIONAL CONFERENCE ON ADVANCED MATERIALS AND PROCESSING, PTS 1-5, 2005, 475-479 : 2945 - 2948
[39] EFFECT OF STRESS STATE ON CAVITATION AND HOLE GROWTH IN SUPERPLASTIC AA-7475 ALUMINUM-ALLOY
GUO, ZX
RIDLEY, N
MATERIALS SCIENCE AND TECHNOLOGY, 1990, 6 (06) : 516 - 519
[40] HIGH-TEMPERATURE DEFORMATION IN A SUPERPLASTIC 7475-AL-ALLOY WITH A RELATIVELY LARGE GRAIN-SIZE
SHIN, DH
PARK, KT
LAVERNIA, EJ
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1995, 201 (1-2): : 118 - 126

← 1 2 3 4 5 →