Wear model in turning of hardened steel with PCBN tool

被引：25
|
作者：
Camargo, Jose C. [1 ]
Dominguez, Dany Sanchez [1 ]
Ezugwu, Emmanuel O. [2 ]
Machado, Alisson R. [3 ]
机构：
[1] Univ Estadual Santa Cruz, Sch Mech Engn, Lab Mfg, BR-45662900 Ilheus, BA, Brazil
[2] Nigerian Air Force Base, Air Force Inst Technol, Kaduna, Nigeria
[3] Univ Fed Uberlandia, Sch Mech Engn, Lab Teaching & Res Machining, BR-38408100 Santa Monica, MG, Brazil
来源：
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS | 2014年 / 47卷
关键词：
Tool wear model; AISI D6 steel; PCBN tool; Hard turning;
D O I：
10.1016/j.ijrmhm.2014.06.019
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
In this study a mathematical-computational model of tool wear of PCBN (polycrystalline cubic boron nitride) was developed in turning of quenched and tempered AISI D6 steel (57 HRC) using experimental planning and statistic techniques. On the experimental trials many parameters are important such as: surface roughness, cutting force and tool wear. These parameters were evaluated according to their statistical significance using Statistica (R) and Matlab (R) softwares. Through a multiple-regression analysis, it was possible to establish a mathematical model for estimating tool wear as a function of the cutting parameters. This model enhanced estimation of the ideal cutting conditions for turning hardened steel, i.e., those that generate minimum damage on the PCBN tool without compromising productivity. (C) 2014 Elsevier Ltd. All rights reserved.
引用
收藏
页码：61 / 70
页数：10
相关论文
共 50 条
  • [31] Mechanistic modeling of cutting forces and tool flank wear in the thermally enhanced turning of hardened steel
    Farahnakian, M.
    Elhami, S.
    Daneshpajooh, H.
    Razfar, M. R.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 88 (9-12): : 2969 - 2983
  • [32] Wear behaviour of CBN tool when turning hardened AISI D3 steel
    Bouchelaghem, H.
    Yallese, M. A.
    Amirat, A.
    Belhadi, S.
    MECHANIKA, 2007, (03): : 57 - 65
  • [33] Mechanistic modeling of cutting forces and tool flank wear in the thermally enhanced turning of hardened steel
    M. Farahnakian
    S. Elhami
    H. Daneshpajooh
    M. R. Razfar
    The International Journal of Advanced Manufacturing Technology, 2017, 88 : 2969 - 2983
  • [34] Effect of Process Parameters on Tool Wear and Surface Roughness during Turning of Hardened Steel with Coated Ceramic Tool
    Suresh, R.
    Basavarajappa, S.
    INTERNATIONAL CONFERENCE ON ADVANCES IN MANUFACTURING AND MATERIALS ENGINEERING (ICAMME 2014), 2014, 5 : 1450 - 1459
  • [35] Tool wear in milling hardened die steel
    Nelson, S
    Schueller, JK
    Tlusty, J
    JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 1998, 120 (04): : 669 - 673
  • [36] Tool wear in milling hardened die steel
    Univ of Florida, Gainesville, United States
    J Manuf Sci Eng Trans ASME, 4 (669-673):
  • [37] Tool wear rate of the PCBN, mixed ceramic, and coated cemented carbide in the hard turning of the AISI 52100 steel
    Boing, Denis
    Zilli, Leonardo
    Fries, Carlos Ernani
    Schroeter, Rolf Bertrand
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 104 (9-12): : 4697 - 4704
  • [38] Tool wear rate of the PCBN, mixed ceramic, and coated cemented carbide in the hard turning of the AISI 52100 steel
    Denis Boing
    Leonardo Zilli
    Carlos Ernani Fries
    Rolf Bertrand Schroeter
    The International Journal of Advanced Manufacturing Technology, 2019, 104 : 4697 - 4704
  • [39] High speed continuous turning of hardened steel with newly developed low content PCBN
    Lee Sang-Yong
    Park Byong-Joon
    Oh Jeang Ook
    金刚石与磨料磨具工程, 2008, (S1) : 80 - 82
  • [40] Analyses of Tool Wear and Chip Type for Different Coated Carbide Inserts in Turning Hardened 1.6582 Steel
    Sramhauser, Karel
    Naprstkova, Natasa
    Sviantek, Jan
    Stancekova, Dana
    Nguyen Van Tuong
    Novotny, Jan
    COATINGS, 2022, 12 (07)
12345