New printed circuit heat exchanger with S-shaped fins for hot water supplier

被引：204

作者：

Ngo, Tri Lam ^{[1
]}

Kato, Yasuyoshi ^{[1
]}

Nikitin, Konstantin ^{[1
]}

Tsuzuki, Nobuyoshi ^{[1
]}

机构：

[1] Tokyo Inst Technol, Nucl Reactors Res Lab, Meguro Ku, Tokyo 1528550, Japan

来源：

EXPERIMENTAL THERMAL AND FLUID SCIENCE | 2006年 / 30卷 / 08期

关键词：

printed circuit heat exchanger; supercritical CO2; hot water supplier; waste heat recovery; overall heat transfer coefficient; pressure drop;

D O I：

10.1016/j.expthermflusci.2006.03.010

中图分类号：

O414.1 [热力学];

学科分类号：

摘要：

A new PCHE with an S-shaped fin configuration was applied to a hot water supplier in which cold water of 7 degrees C is warmed to 90 degrees C through heat-exchange with supercritical CO2 of 118 degrees C and 11.5 MPa pressure. The fin and plate configurations were determined using 3D CFD simulations for the CO2 side and H2O side and the thermal-hydraulic performance of hot water supplier was evaluated. Compared with a hot water supplier that is currently used in a residential heat pump, the new PCHE provides about 3.3 times less volume; and lower pressure drop by 37% in the CO2 side and by 10 times in H2O side. (C) 2006 Elsevier Inc. All rights reserved.

引用

页码：811 / 819

页数：9

共 50 条

[31] Review of optimization and heat transfer correlations of printed circuit heat exchanger
Yang G.
Shao W.
Huagong Jinzhan/Chemical Industry and Engineering Progress, 2021, 40 (S1): : 13 - 26
[32] Effect of tangled channels on the heat transfer in a printed circuit heat exchanger
Sung, Joonyoung
Lee, Jae Young
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2017, 115 : 647 - 656
[33] Simulation of the printed circuit heat exchanger for S-CO2 by segmented methods
Ke, Hanbing
Xiao, Qi
Cao, Yiping
Ma, Ting
Lin, Yuansheng
Zeng, Min
Wang, Qiuwang
PROCEEDINGS OF THE 9TH INTERNATIONAL CONFERENCE ON APPLIED ENERGY, 2017, 142 : 4098 - 4103
[34] Numerical analysis of S-CO2 heat transfer characteristics in a printed circuit heat exchanger
Liu K.
Ming Y.
Hu C.
Zhao F.
Yu L.
Tian R.
Harbin Gongcheng Daxue Xuebao/Journal of Harbin Engineering University, 2021, 42 (12): : 1777 - 1785
[35] THERMAL-HYDRAULIC PERFORMANCE OF DIFFERENT DISCONTINUOUS FINS USED IN A PRINTED CIRCUIT HEAT EXCHANGER FOR SUPERCRITICAL CO2
Xu, X. Y.
Wang, Q. W.
Li, L.
Ekkad, S. V.
Ma, T.
NUMERICAL HEAT TRANSFER PART A-APPLICATIONS, 2015, 68 (10) : 1067 - 1086
[36] Numerical Analysis of Tube Heat Exchanger with Perforated Star-Shaped Fins
Bosnjakovic, Mladen
Muhic, Simon
FLUIDS, 2020, 5 (04)
[37] Numerical Analysis of Tube Heat Exchanger with Trimmed Star-Shaped Fins
Bosnjakovic, Mladen
Muhic, Simon
APPLIED SCIENCES-BASEL, 2022, 12 (10):
[38] Development of tritium permeation model for Printed Circuit Heat Exchanger
Park, Min Young
Song, Min Seop
Kim, Eung Soo
ANNALS OF NUCLEAR ENERGY, 2016, 98 : 166 - 177
[39] Optimization of Printed Circuit Heat Exchanger Using Exergy Analysis
Lee, Sang-Moon
Kim, Kwang-Yong
JOURNAL OF HEAT TRANSFER-TRANSACTIONS OF THE ASME, 2015, 137 (06):
[40] HEAT TRANSFER OF SUPERCRITICAL CARBON DIOXIDE IN PRINTED CIRCUIT HEAT EXCHANGER GEOMETRIES
Kruizenga, Alan
Anderson, Mark
Fatima, Roma
Corradini, Michael
Towne, Aaron
Ranjan, Devesh
PROCEEDINGS OF THE ASME INTERNATIONAL HEAT TRANSFER CONFERENCE - 2010, VOL 4: HEAT TRANSFER MEASUREMENT TECHNIQUES, HEAT TRANSFER EQUIPMENT, THERMOELECTRICS, 2010, : 653 - 661

← 1 2 3 4 5 →