Development and characterization of dissimilar joint between AA2024-T3 and AA6061-T6 by modified friction stir clinching process

被引：40
|
作者：
Paidar, M. [1 ]
Vignesh, R. Vaira [2 ]
Moharrami, A. [3 ]
Ojo, O. O. [4 ]
Jafari, A. [5 ]
Sadreddini, S. [6 ]
机构：
[1] Islamic Azad Univ, Dept Mat Engn, South Tehran Branch, Tehran 1459853849, Iran
[2] Amrita Vishwa Vidyapeetham, Dept Mech Engn, Amrita Sch Engn, Coimbatore, Tamil Nadu, India
[3] Pishroghaleb Simindasht Ind Prod Co, Dept Res & Dev, Simindasht Ind Pk, Alborz, Iran
[4] Fed Univ Technol Akure, Dept Ind & Prod Engn, Akure, Nigeria
[5] South Ural State Univ, 76 Lenin Aven, Chelyabinsk 454080, Russia
[6] Islamic Azad Univ, Sci & Res Branch, Young Researchers & Elites Club, Tehran, Iran
来源：
VACUUM | 2020年 / 176卷
关键词：
Microstructure; Friction stir clinching; Aluminum; Dissimilar; Welding; MECHANICAL-PROPERTIES; ALUMINUM-ALLOY; FATIGUE LIFE; MICROSTRUCTURE; TOOL; STRENGTH; DESIGN;
D O I：
10.1016/j.vacuum.2020.109298
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Friction stir spot welding (FSSW) is one of the effective solid-state welding strategies to achieve good joint efficiency between dissimilar aluminum alloys. However, the formation of tool-induced keyhole (a stress raiser) is inevitable during the FSSW process. This study explores the possibility of eliminating keyhole with the aim of improving the properties of the joint by Modified Friction Stir Clinching (MFSC) process. The tensile-shear and cross-tension strengths of the MFSC joints are 83% and 50% higher than that of the specimens joined by FSSW. The article presents a comprehensive analysis of the material flow characteristics, microstructural evolution, and tensile properties of the dissimilar joints between AA2024-T3 and AA6061-T6 that was enabled by the MFSC process.
引用
收藏
页数：6
相关论文
共 50 条
  • [31] Effects of materials positioning and tool rotational speed on metallurgical and mechanical properties of dissimilar modified friction stir clinching of AA5754-O and AA2024-T3 sheets
    Memon, S.
    Paidar, M.
    Mehrez, S.
    Cooke, K.
    Ojo, O. O.
    Lankarani, H. M.
    RESULTS IN PHYSICS, 2021, 22
  • [32] Stochastic Tensile Failure Analysis on Dissimilar AA6061-T6 with AA7075-T6 Friction Stir Welded Joints and Predictive Modeling
    Thella Babu Rao
    Journal of Failure Analysis and Prevention, 2020, 20 : 1333 - 1350
  • [33] ANALYSIS AND CHARACTERIZATION OF FORMING BEHAVIOR ON DISSIMILAR JOINTS OF AA5052-O TO AA6061-T6 USING UNDERWATER FRICTION STIR WELDING
    Babu, K. Tejonadha
    Muthukumaran, S.
    Narayanan, C. Sathiya
    Kumar, C. H. Bharat
    SURFACE REVIEW AND LETTERS, 2020, 27 (03)
  • [34] Feasibility study on dissimilar joint between Alclad AA2024-T3 and DC04 steel by friction stir welding
    Mysliwisec, Piotr
    Kubit, Andrzej
    Derazkola, Hamed Aghajani
    Szawara, Paulina
    Slota, Jan
    MATERIALS TODAY COMMUNICATIONS, 2024, 38
  • [35] Comparison of the Weldability of AA6061-T6 Joint under Different Friction Stir Welding Conditions
    Abdollahzadeh, Amin
    Bagheri, Behrouz
    Abassi, Mahmoud
    Kokabi, Amir Hossein
    Moghaddam, Ahmad Ostovari
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2021, 30 (02) : 1110 - 1127
  • [36] Comparison of the Weldability of AA6061-T6 Joint under Different Friction Stir Welding Conditions
    Amin Abdollahzadeh
    Behrouz Bagheri
    Mahmoud Abassi
    Amir Hossein Kokabi
    Ahmad Ostovari Moghaddam
    Journal of Materials Engineering and Performance, 2021, 30 : 1110 - 1127
  • [37] Pinless Friction Stir Welding of AA2024-T3 Joint and Its Failure Modes
    李文亚
    李锦锋
    张志函
    高大路
    王卫兵
    栾国红
    Transactions of Tianjin University, 2014, (06) : 439 - 443
  • [38] Pinless Friction Stir Welding of AA2024-T3 Joint and Its Failure Modes
    李文亚
    李锦锋
    张志函
    高大路
    王卫兵
    栾国红
    Transactions of Tianjin University, 2014, 20 (06) : 439 - 443
  • [39] Pinless friction stir welding of AA2024-T3 joint and its failure modes
    Li W.
    Li J.
    Zhang Z.
    Gao D.
    Wang W.
    Luan G.
    Transactions of Tianjin University, 2014, 20 (06) : 439 - 443
  • [40] Modified friction stir clinching of AA6061-T6/AA5754-O joint: Effect of tool rotational speed and solution heat treatment on mechanical, microstructure, and fracture behaviors
    Paidar, M.
    Mehrez, S.
    Ojo, O. O.
    Mohanavel, V.
    Babaei, B.
    Ravichandran, M.
    MATERIALS CHARACTERIZATION, 2021, 173
12345