BENDING STRAINS OF STEEL CONSTRUCTION IN PROCESS OF WELDING BY MAG TECHNOLOGY

被引：0
|
作者：
Verdins, Gunars [1 ]
Kanaska, Daina [1 ]
Kairiss, Mareks [2 ]
机构：
[1] Latvia Univ Agr, Jelgava, Latvia
[2] EASTMETAL Ltd, Dobele, Dobeles Pilseta, Latvia
来源：
14TH INTERNATIONAL SCIENTIFIC CONFERENCE: ENGINEERING FOR RURAL DEVELOPMENT | 2015年
关键词：
welding; weld; bending deformations; breaking jig;
D O I：
暂无
中图分类号：
S2 [农业工程];
学科分类号：
0828 ;
摘要：
Dimensional deformations of a steel beam after MAG welding ere analytically calculated as well as verified by experiment results. There are the key factors defined, which have an effect on the value of deformation as well as solutions offered for regulation of the value of deformation in dependence on the welding technology and by selection of the regime. Experimental studies have shown that in the researched plate by using of indirect bending in breaking jig on the calculated bending angle the deformation of the plate is reduced by 60 %; as a result the flatness after welding corresponds to the tolerance of +/- 4mm.
引用
收藏
页码：778 / 783
页数：6
相关论文
共 50 条
  • [41] Stainless Steel Welding and Development Trend of Welding Technology
    Feng, Lifa
    Yang, Nengjun
    2018 4TH INTERNATIONAL CONFERENCE ON ENVIRONMENTAL SCIENCE AND MATERIAL APPLICATION, 2019, 252
  • [42] IGNITION PROCESS CONTROL IN MAG-WELDING/ STEUERUNG DES ZUENDVORGANGES BEIM MAG-SCHWEISSEN.
    HESSE, GUENTER
    1981, V 23 (N 12): : 1391 - 1411
  • [43] Optimization of MAG welding process parameters using Taguchi design method on dead mild steel used in automotive industry
    Tadele Tesfaw
    Ajit Pal Singh
    Abebaw Mekonnen Gezahegn
    Berhanu Tolosa Garedew
    International Journal of System Assurance Engineering and Management, 2022, 13 : 79 - 89
  • [44] Optimization of MAG welding process parameters using Taguchi design method on dead mild steel used in automotive industry
    Tesfaw, Tadele
    Singh, Ajit Pal
    Gezahegn, Abebaw Mekonnen
    Garedew, Berhanu Tolosa
    INTERNATIONAL JOURNAL OF SYSTEM ASSURANCE ENGINEERING AND MANAGEMENT, 2022, 13 (01) : 79 - 89
  • [45] Simulation of bridge steel structure construction process based on BIM technology
    Pan W.
    Applied Mathematics and Nonlinear Sciences, 2024, 9 (01)
  • [46] Advantages of MAG-STT Welding Process for Root Pass Welding in the Oil and Gas Industry
    Adi, Pandzic
    Ismar, Hajro
    Petar, Tasic
    TEM JOURNAL-TECHNOLOGY EDUCATION MANAGEMENT INFORMATICS, 2016, 5 (01): : 76 - 79
  • [47] Relationship between penetration and porosity in horizontal fillet welding by Hybrid Tandem MAG welding process
    Yuan, Yimin
    Yamazaki, Kei
    Suzuki, Reiichi
    Yosetsu Gakkai Ronbunshu/Quarterly Journal of the Japan Welding Society, 2015, 33 (04): : 349 - 357
  • [48] Energy parameters of weld formation process in MIG-MAG welding
    Chinakhov D.A.
    Solodskii S.A.
    Rodionov P.V.
    Sydorets V.N.
    Materials Science Forum, 2018, 927 MSF : 99 - 105
  • [49] Evaluation of the TIG-MIG/MAG welding process in direct polarity
    da Silva Costa, Gabriella Cristina
    de Resende, Andre Alves
    SN APPLIED SCIENCES, 2020, 2 (02):
  • [50] Process stability and spatter generation during dip transfer in MAG welding
    Gupta, S.R.
    Gupta, P.C.
    Rehfeldt, D.
    Welding Review International, 1988, 7 (04):
12345