Post-ejection cooling behavior of injection molded parts

被引：0
|
作者：
Moller, J [1 ]
Carlson, M [1 ]
Alterovitz, R [1 ]
Swartz, J [1 ]
机构：
[1] Miami Univ, Oxford, OH 45056 USA
来源：
CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS | 1998年 / 44卷
关键词：
D O I：
暂无
中图分类号：
TQ [化学工业];
学科分类号：
0817 ;
摘要：
The quantity of heat and its distribution in an injection molded part at the time of ejection has bearing upon part quality. A method for accurate measurement of part surface temperature from soon after ejection and during cooling has been created. It is found that-following ejection, the mold part's surface quickly heats to approximately the bulk mean temperature. The entire part then cools gradually at nearly uniform temperature. Measured results compare well with predicted behavior. This approach can be used to assess the effectiveness of active die cooling and verify the appropriateness of the selected in-die cooling time.
引用
收藏
页码：525 / 529
页数：5
相关论文
共 50 条
  • [21] Thermoelasticity of Injection-Molded Parts
    Turk, Janez
    Svensek, Daniel
    POLYMERS, 2023, 15 (13)
  • [22] Morphology Distribution in Injection Molded Parts
    Liparoti, Sara
    Salomone, Rita
    Speranza, Vito
    Pantani, Roberto
    POLYMERS, 2024, 16 (03)
  • [23] Optimizing injection-molded parts
    Deitz, D
    MECHANICAL ENGINEERING, 1996, 118 (10) : 89 - 90
  • [24] Surface Homogeneity of Injection Molded Parts
    Zsiros, Laszlo
    Kovacs, Jozsef Gabor
    PERIODICA POLYTECHNICA-MECHANICAL ENGINEERING, 2018, 62 (04): : 284 - 291
  • [25] Shrinkage computation of injection molded parts
    Zhu, Tieli
    Wang, Minjie
    Jixie Gongcheng Xuebao/Chinese Journal of Mechanical Engineering, 2002, 38 (09): : 145 - 149
  • [26] Morphology-Property Behavior of Semi Crystalline Polymers in Injection Molded Parts
    Spoerer, Y.
    Blanco, C.
    Zimmermann, M.
    Berger, M.
    Kuehnert, I
    PROCEEDINGS OF THE EUROPE/AFRICA CONFERENCE DRESDEN 2017 - POLYMER PROCESSING SOCIETY PPS, 2019, 2055
  • [27] ON THE INFLUENCE OF PROCESSING TEMPERATURE ON THE MECHANICAL-BEHAVIOR OF INJECTION-MOLDED PARTS
    CRIENS, RM
    MOSLE, HG
    PLASTICS ENGINEERING, 1984, 40 (03) : 60 - 60
  • [28] Capturing PVT behavior of injection-molded parts using hybrid methods
    Lobo, H
    Bethard, T
    ANTEC '99: PLASTICS BRIDGING THE MILLENNIA, CONFERENCE PROCEEDINGS, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPECIAL AREAS;, 1999, : 788 - 793
  • [29] Effect of Compatibility on the Foaming Behavior of Injection Molded Polypropylene and Polycarbonate Blend Parts
    Su, Bei
    Zhou, Ying-Guo
    Dong, Bin-Bin
    Yan, Cao
    POLYMERS, 2019, 11 (02)
  • [30] AN ANALYSIS OF THERMAL WARPAGE IN INJECTION MOLDED FLAT PARTS DUE TO UN-BALANCED COOLING
    STJACQUES, M
    POLYMER ENGINEERING AND SCIENCE, 1982, 22 (04): : 241 - 247
12345