Post-ejection cooling behavior of injection molded parts

被引：0

作者：

Moller, J ^{[1
]}

Carlson, M ^{[1
]}

Alterovitz, R ^{[1
]}

Swartz, J ^{[1
]}

机构：

[1] Miami Univ, Oxford, OH 45056 USA

来源：

CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS | 1998年 / 44卷

关键词：

D O I：

暂无

中图分类号：

TQ [化学工业];

学科分类号：

0817 ;

摘要：

The quantity of heat and its distribution in an injection molded part at the time of ejection has bearing upon part quality. A method for accurate measurement of part surface temperature from soon after ejection and during cooling has been created. It is found that-following ejection, the mold part's surface quickly heats to approximately the bulk mean temperature. The entire part then cools gradually at nearly uniform temperature. Measured results compare well with predicted behavior. This approach can be used to assess the effectiveness of active die cooling and verify the appropriateness of the selected in-die cooling time.

引用

页码：525 / 529

页数：5

共 50 条

[11] A simple method of improving warpage and cooling time of injection molded parts simultaneously
Kuo, Chil-Chyuan
Xu, Yu-Xin
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2022, 122 (02): : 619 - 637
[12] Stress analysis of injection molded parts in post-filling stage
Tao, Jiang
Xing, Chen
Dequn, Li
Chinese Journal of Mechanical Engineering (English Edition), 2000, 13 (01): : 41 - 46
[13] STRESS ANALYSIS OF INJECTION MOLDED PARTS IN POST-FILLING STAGE
Jiang Tao
Chen Xing
Li Dequn (National Key ho of Plastic Simulation & Molding Technology
Huazhong University of Science & Technology)
Chinese Journal of Mechanical Engineering(English Edition), 2000, (01) : 41 - 46
[14] COOLING MOLDED PARTS - A RIGOROUS ANALYSIS
KENIG, S
KAMAL, MR
SPE JOURNAL, 1970, 26 (07): : 50 - &
[15] Investigation of compression behavior of PE/EVA foam injection molded parts
Spina, Roberto
PROCEEDINGS OF THE 20TH INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2017), 2017, 1896
[16] Shrinkage behavior and optimization of injection molded parts studied by the Taguchi method
Chang, TC
Faison, E
POLYMER ENGINEERING AND SCIENCE, 2001, 41 (05): : 703 - 710
[17] Experimental assessment and optimization of shrinkage behavior of injection molded polycarbonate parts
Azdast, Taher
Hasanzadeh, Rezgar
MATERIALS RESEARCH EXPRESS, 2019, 6 (11)
[18] How low can you go? Optimizing the cooling of small injection molded parts
Dowler, B
Coppari, L
ANTEC'97 - PLASTICS SAVING PLANET EARTH, CONFERENCE PROCEEDINGS, VOLS 1 - 3, 1997, : 946 - 953
[19] How low can you go? Optimizing the cooling of small injection molded parts
Dowler, B
Coppari, L
PLASTICS ENGINEERING, 1997, 53 (06) : 29 - 32
[20] NEW DESIGN OF INJECTION MOLDED PARTS
BEALL, G
KUNSTSTOFFE-GERMAN PLASTICS, 1990, 80 (08): : 911 - 914

← 1 2 3 4 5 →