Spark Plasma Sintering Process of Fe-6.5%Si alloy from Fe and FeSi Powders

被引：1
|
作者：
Zhang Xiang [1 ]
Li Junguo [1 ]
Qi Qingqing [1 ]
Zhang Lianmeng [1 ]
机构：
[1] Wuhan Univ Technol, Wuhan 430070, Peoples R China
来源：
ADVANCED SYNTHESIS AND PROCESSING TECHNOLOGY FOR MATERIALS | 2009年 / 66卷
关键词：
Silicon steel; SPS; sintering process; MAGNETIC-PROPERTIES;
D O I：
10.4028/www.scientific.net/AMR.66.270
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Powder metallurgy (PM) method to fabricate 6.5% silicon steel attracts much attention due to the lower energy consumption and cost. In this paper, Fe-6 5%Si alloy was prepared by spark plasma sintering (SPS) from the mixture of Fe and Fe Si powders with different size The sintering process was investigated through the shrinkage behavior, phase change and microstructure The results show that the shrinkage starts from 500 degrees C, lower than conventional sintering methods The sintering temperature and Fe Si powder size influence the reaction between Fe and FeSi
引用
收藏
页码：270 / 272
页数：3
相关论文
共 50 条
  • [41] Spark plasma sintering of Nd-Fe-B magnetic alloy
    Liu, ZG
    Umemoto, M
    Hirosawa, S
    Kanekiyo, H
    JOURNAL OF MATERIALS RESEARCH, 1999, 14 (06) : 2540 - 2547
  • [42] Spark plasma sintering of Nd-Fe-B magnetic alloy
    Dept. of Prod. Systems Engineering, Toyohashi University of Technology, 1-1 Tempaku-cho, Toyohashi 441, Japan
    不详
    J Mater Res, 6 (2540-2547):
  • [43] The Addition of Boron to Melt-Spun Fe-6.5%Si Ribbons
    Ouyang, Gaoyuan
    Claude, Roger
    Kovar, Alexander
    Hillard, Ben
    Kramer, Matthew J.
    Anderson, Iver E.
    Cui, Jun
    JOM, 2024, 76 (03) : 1044 - 1049
  • [44] Fe-6.5%Si粉末的混合与特性研究
    员文杰
    李俊国
    沈强
    张联盟
    中国粉体技术, 2007, (02) : 18 - 20
  • [45] Fe-6.5%Si合金冷轧薄板的冲压性能
    严李李
    房现石
    梁永锋
    叶丰
    林均品
    材料工程, 2012, (06) : 28 - 31
  • [46] Fe-6.5%Si钢极薄带的试制
    曾春
    程朝阳
    王项龙
    吴章汉
    钢铁, 2022, 57 (01) : 126 - 132
  • [47] EFFECT OF GRAIN-BOUNDARY CARBIDES ON THE DUCTILITY OF AN FE-6.5 WI-PERCENT SI ALLOY
    BHAGWAT, AW
    MICHAL, GM
    JOURNAL OF METALS, 1988, 40 (07): : A60 - A60
  • [48] THE EFFECT OF DYNAMIC ELECTROPULSING ON MECHANICAL AND MICROSTRUCTUAL PROPERTIES OF COLD ROLLED Fe-6.5% Si ALLOY SHEET
    Liang, Y. F.
    Ye, F.
    Zhou, H. C.
    Wang, F. M.
    Tang, G. Y.
    Lin, J. P.
    ENERGY TECHNOLOGY 2012: CARBON DIOXIDE MANAGEMENT AND OTHER TECHNOLOGIES, 2012, : 289 - 295
  • [49] Effects of grain boundary and grain orientation on bend behavior of directionally solidified Fe-6.5%Si alloy
    Song, H.W.
    Lin, D.L.
    Shan, A.D.
    Chen, J.G.
    Wang, C.
    Shanghai Jiaotong Daxue Xuebao/Journal of Shanghai Jiaotong University, 2001, 35 (05): : 655 - 659
  • [50] Slip in directionally solidified Fe-6.5%Si alloy during three-point bending at RT
    Song, H.W.
    Lin, D.L.
    Shan, A.D.
    Chen, J.G.
    Wang, C.
    2001, Shanghai Jiao Tong University (35):
12345