Investigation of the Effect of Zirconium Amount on Grain Size and Wear Performance in TZM Alloys Produced by Mechanical Alloying Method

被引：1

作者：

Sirali, Haktan ^{[1
]}

Simsek, Dogan ^{[2
]}

Ozyurek, Dursun ^{[3
]}

机构：

[1] Karabuk Univ, Inst Sci, Karabuk, Turkey

[2] Natl Def Univ, Army NCO Vocat HE Sch, Balikesir, Turkey

[3] Karabuk Univ, Technol Fac, Karabuk, Turkey

来源：

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS | 2022年 / 75卷 / 03期

关键词：

TZM alloy; Zirconium; Grain size; Wear; BEHAVIOR;

D O I：

10.1007/s12666-021-02510-4

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

In this study, the relation between grain size, hardness and wear performance of Titanium-Zirconium-Molybdenum (TZM) alloys with different amounts (0.06, 0.07, 0.08 and 0.09 wt%) of Zr added by the mechanical alloying method was investigated. As a result of the studies, it was observed that the number of pores in the structure increased with the increase in the amount of Zr, while there was a decrease in the grain size. In the hardness and density results, it was observed that while the hardness values increased with increasing Zr amount, there was a decrease in the density values. As a result of the wear tests, the lowest weight loss at 10-30 N loads was obtained in the TZM alloy with the highest Zr added (0.09% Zr). The lowest friction coefficient in the friction coefficient results was obtained in TZM alloy with 0.09% Zr added.

引用

页码：805 / 812

页数：8

共 50 条

[41] Effect of recrystallisation and grain size on the mechanical properties of spray formed AlCuMgAg-alloys
Eschbach, L
Uggowitzer, PJ
Speidel, MO
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1998, 248 (1-2): : 1 - 8
[42] Experimental investigations of the effect of various alloying elements on As-cast grain size of wrought Al-alloys
Vatne, HE
Håkonsen, A
LIGHT METALS 1999, 1999, : 787 - 792
[43] The Effect of Porosity and Grain Size on the Phase Composition and Mechanical Properties of Zirconium-Dioxide-Based Ceramic
N. L. Savchenko
T. Yu. Sablina
I. N. Sevost’yanova
A. G. Burlachenko
S. P. Buyakova
S. N. Kul’kov
Technical Physics Letters, 2018, 44 : 663 - 666
[44] The Effect of Porosity and Grain Size on the Phase Composition and Mechanical Properties of Zirconium-Dioxide-Based Ceramic
Savchenko, N. L.
Sablina, T. Yu.
Sevost'yanova, I. N.
Burlachenko, A. G.
Buyakova, S. P.
Kul'kov, S. N.
TECHNICAL PHYSICS LETTERS, 2018, 44 (08) : 663 - 666
[45] Effect of annealing on microstructure, grain growth, and hardness of nanocrystalline Fe-Ni alloys prepared by mechanical alloying
Kotan, H.
Saber, M.
Koch, C. C.
Scattergood, R. O.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 552 : 310 - 315
[46] Effect of grain refinement on the performance of AZ80 Mg alloys during wear and corrosion
Naik, Gajanan M.
Gote, Gopal D.
Narendranath, S.
Kumar, S. S. Satheesh
ADVANCES IN MATERIALS RESEARCH-AN INTERNATIONAL JOURNAL, 2018, 7 (02): : 105 - 118
[47] Effect of reinforcement particle size on microstructure and mechanical properties of AlZnMgCu/AlN nano-composites produced using mechanical alloying
Gajewska, Marta
Dutkiewicz, Jan
Morgiel, Jerzy
JOURNAL OF ALLOYS AND COMPOUNDS, 2014, 586 : S423 - S427
[48] Exchange of experience the effect of synthesis time on the wear behavior of Al-8%Ti alloy produced by mechanical alloying
Ozyurek, D.
Tekeli, S.
Tuncay, T.
Yilmaz, R.
POWDER METALLURGY AND METAL CERAMICS, 2012, 51 (7-8) : 491 - 495
[49] Bimodal grain size distributions in UFG materials produced by SPD: Their evolution and effect on mechanical properties
Hoeppel, H. W.
Korn, M.
Lapovok, R.
Mughrabi, H.
15TH INTERNATIONAL CONFERENCE ON THE STRENGTH OF MATERIALS (ICSMA-15), 2010, 240
[50] The Effect of the Elements Co and Ni on Wear Behaviour of Bronze Alloys Produced by the Hot Pressing Method
Yildiz, Tulay
Kati, Nida
Yilmaz, Alaattin
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2021, 74 (04) : 881 - 889

← 1 2 3 4 5 →