Influence of electrical discharge machining on sliding friction and wear of WC-Ni cemented carbide

被引：20
|
作者：
Bonny, K. [1 ]
De Baets, P. [1 ]
Van Wittenberghe, J. [1 ]
Delgado, Y. Perez [1 ]
Vleugels, J. [2 ]
Van der Biest, O. [2 ]
Lauwers, B. [3 ]
机构：
[1] Ghent Univ UGent, Mech Construct & Prod Dept, BE-9000 Ghent, Belgium
[2] Catholic Univ Leuven KU Leuven, Dept Met & Mat Engn, BE-3001 Louvain, Belgium
[3] Catholic Univ Leuven KU Leuven, Dept Mech Engn, BE-3001 Louvain, Belgium
来源：
TRIBOLOGY INTERNATIONAL | 2010年 / 43卷 / 12期
关键词：
WC-Ni cemented carbide; Wire-EDM; Dry reciprocating sliding; Pin-on-plate; TRIBOLOGICAL CHARACTERISTICS; ELECTROCHEMICAL-BEHAVIOR; CO; EDM; RESISTANCE; HARDMETALS; STRENGTH; FRACTURE; NANOCOMPOSITES; CORROSION;
D O I：
10.1016/j.triboint.2010.08.008
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Tribological characteristics of fine-grained WC-8 wt%Ni with different surface finishing conditions corresponding to sequential wire electrical discharge machining (wire-EDM) or grinding were investigated by performing dry reciprocating sliding experiments on TE77 pin-on-plate equipment with WC-6 wt%Co as mating material. Surface finishes and wear surfaces were characterized using surface topography scanning, SEM analysis and EDX spectrometry. The decreased wear resistance due to wire-EDM could be linked to flexural strength properties as well as XRD measurements revealing tensile residual stresses on wire-EDM surfaces, in contrast with the compressive stress state on ground surfaces. Substantial improvement of wear resistance was accomplished with finer-executed EDM steps. (C) 2010 Elsevier Ltd. All rights reserved.
引用
收藏
页码：2333 / 2344
页数：12
相关论文
共 50 条
  • [31] Influence of EDM on the wear characteristics of WC-Co cemented carbide
    Ishikawa, Kaneto
    Iwabuchi, Akira
    Shimizu, Tomoharu
    2003, Japanese Society of Tribologists (48):
  • [32] Tribological behavior of WC-Ni cemented carbide irradiated by high-intensity pulsed ion beam
    Zhang Fenggang
    Zhu Xiaopeng
    Lei Mingkai
    SURFACE & COATINGS TECHNOLOGY, 2014, 258 : 78 - 85
  • [33] RECYCLING OF WC-Ni SCRAP TO OBTAIN TUNGSTEN CARBIDE
    Sknar, Yuri E.
    Kozhura, Oleg V.
    Butyrina, Tetiana E.
    Kuznetsov, Mykola V.
    JOURNAL OF CHEMISTRY AND TECHNOLOGIES, 2024, 32 (03): : 731 - 739
  • [34] SURFACE MODIFICATION OF WC-Ni CEMENTED CARBIDE FOR SEALS BY HIGH INTENSITY PULSED ION BEAM IRRADIATION
    Zhang Fenggang
    Zhu Xiaopeng
    Wang Mingyang
    Lei Mingkai
    ACTA METALLURGICA SINICA, 2011, 47 (07) : 958 - 964
  • [35] Fabrication of Ultrafine WC-Ni Cemented Carbide by Coupled Multi-physical Fields Activated Sintering
    Zhou Yu
    Jiang Wei
    Chen Yitong
    Yang Yi
    Yang Gang
    Yin Degiang
    Liu Jian
    RARE METAL MATERIALS AND ENGINEERING, 2017, 46 (02) : 561 - 564
  • [36] Wear of WC inserts textured by shot peening and electrical discharge machining
    Qi, Ye
    Nguyen, Vinh
    Melkote, Shreyes
    Varenberg, Michael
    Wear, 2021, 452-453
  • [37] Sliding wear behavior of SPS processed TaC-containing Ti(CN)-WC-Ni/Co cermets against Silicon Carbide
    Verma, Vikas
    Kumar, B. V. Manoj
    WEAR, 2017, 376 : 1570 - 1579
  • [38] Wear of WC inserts textured by shot peening and electrical discharge machining
    Qi, Ye
    Nguyen, Vinh
    Melkote, Shreyes
    Varenberg, Michael
    WEAR, 2020, 452
  • [39] Sliding Wear of Electrically Conductive ZrO2−WC Composites Against WC–Co Cemented Carbide
    K. Bonny
    P. De Baets
    J. Vleugels
    A. Salehi
    O. Van der Biest
    B. Lauwers
    W. Liu
    Tribology Letters, 2008, 30
  • [40] Sliding Wear Behavior of TaC-Containing Ti(CN)-WC-Ni/Co Cermets
    Verma, Vikas
    Kumar, B. Venkata Manoj
    Kang, Shinhoo
    INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY, 2016, 13 (06) : 1033 - 1042
12345