Influence of electrical discharge machining on sliding friction and wear of WC-Ni cemented carbide

被引：20

作者：

Bonny, K. ^{[1
]}

De Baets, P. ^{[1
]}

Van Wittenberghe, J. ^{[1
]}

Delgado, Y. Perez ^{[1
]}

Vleugels, J. ^{[2
]}

Van der Biest, O. ^{[2
]}

Lauwers, B. ^{[3
]}

机构：

[1] Ghent Univ UGent, Mech Construct & Prod Dept, BE-9000 Ghent, Belgium

[2] Catholic Univ Leuven KU Leuven, Dept Met & Mat Engn, BE-3001 Louvain, Belgium

[3] Catholic Univ Leuven KU Leuven, Dept Mech Engn, BE-3001 Louvain, Belgium

来源：

TRIBOLOGY INTERNATIONAL | 2010年 / 43卷 / 12期

关键词：

WC-Ni cemented carbide; Wire-EDM; Dry reciprocating sliding; Pin-on-plate; TRIBOLOGICAL CHARACTERISTICS; ELECTROCHEMICAL-BEHAVIOR; CO; EDM; RESISTANCE; HARDMETALS; STRENGTH; FRACTURE; NANOCOMPOSITES; CORROSION;

D O I：

10.1016/j.triboint.2010.08.008

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

Tribological characteristics of fine-grained WC-8 wt%Ni with different surface finishing conditions corresponding to sequential wire electrical discharge machining (wire-EDM) or grinding were investigated by performing dry reciprocating sliding experiments on TE77 pin-on-plate equipment with WC-6 wt%Co as mating material. Surface finishes and wear surfaces were characterized using surface topography scanning, SEM analysis and EDX spectrometry. The decreased wear resistance due to wire-EDM could be linked to flexural strength properties as well as XRD measurements revealing tensile residual stresses on wire-EDM surfaces, in contrast with the compressive stress state on ground surfaces. Substantial improvement of wear resistance was accomplished with finer-executed EDM steps. (C) 2010 Elsevier Ltd. All rights reserved.

引用

页码：2333 / 2344

页数：12

共 50 条

[11] Cold gas dynamic spraying of WC-Ni cemented carbide coatings
Lioma, D.
Sacks, N.
Botef, I.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2015, 49 : 365 - 373
[12] Mechanical properties of micro-grained WC-Ni cemented carbide
Funtai Oyobi Fummatsu Yakin, 11 (1345):
[13] Influence of electrical discharge machining on the sliding contact response of cemented carbides
Llanes, L
Idañez, E
Martínez, E
Casas, B
Esteve, J
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2001, 19 (01): : 35 - 40
[14] Friction and Wear Properties of HfC-WC-Co Cemented Carbide
Yan, X. Y.
Wang, S. R.
Chen, S. S.
Xue, C. Y.
4TH INTERNATIONAL CONFERENCE ON MECHANICAL AND AERONAUTICAL ENGINEERING (ICMAE 2018), 2019, 491
[15] Some study on electrical discharge machining of ({WC+TiC+TaC/NbC}–Co) cemented carbide
Simul Banerjee
Debasish Mahapatro
Shishir Dubey
The International Journal of Advanced Manufacturing Technology, 2009, 43 : 1177 - 1188
[16] Effect of ultrasonic vibration of tool on electrical discharge machining of cemented tungsten carbide (WC-Co)
Amir Abdullah
Mohammad R. Shabgard
The International Journal of Advanced Manufacturing Technology, 2008, 38 : 1137 - 1147
[17] Effect of ultrasonic vibration of tool on electrical discharge machining of cemented tungsten carbide (WC-Co)
Abdullah, Amir
Shabgard, Mohammad R.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2008, 38 (11-12): : 1137 - 1147
[18] Electrical discharge machining (EDM) characteristics associated with electrical discharge energy on machining of cemented tungsten carbide
Lin, Yan-Cherng
Chen, Yuan-Feng
Lin, Ching-Tien
Tzeng, Hsinn-Jyh
MATERIALS AND MANUFACTURING PROCESSES, 2008, 23 (3-4) : 391 - 399
[19] Dry Sliding Friction and Wear Behavior of WC/WC-Ni Particles Laser Cladding Reinforced by Nano TiC on Mold Steel Surface
Yang, Qiuhe
Guo, Shaoyi
Wang, Lixia
Li, Xingjun
MANUFACTURING PROCESS TECHNOLOGY, PTS 1-5, 2011, 189-193 : 3721 - +
[20] Wear behavior of WC-Ni sliding against graphite under water lubrication
Zhang, Gaolong
Liu, Ying
Wang, Yuechang
Guo, Fei
Liu, Xiangfeng
Wang, Yuming
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2017, 33 (11) : 1346 - 1352

← 1 2 3 4 5 →