Strength and porosity of additively manufactured PLA using a low cost 3D printing

被引：0
|
作者：
Habeeb, H. A. [1 ,3 ]
Alkahari, M. R. [1 ,2 ]
Ramli, F. R. [1 ,2 ]
Hasan, R. [1 ,2 ]
Maidin, S. [1 ,2 ]
机构：
[1] Univ Teknikal Malaysia Melaka, Fac Mech Engn, Durian Tunggal 76100, Melaka, Malaysia
[2] Univ Teknikal Malaysia Melaka, Ctr Adv Res Energy, Durian Tunggal 76100, Melaka, Malaysia
[3] Univ Teknikal Malaysia Melaka, Fac Mfg Engn, Durian Tunggal 76100, Melaka, Malaysia
来源：
PROCEEDINGS OF MECHANICAL ENGINEERING RESEARCH DAY 2016 | 2016年
关键词：
3D printing; additive manufacturing; rapid prototyping; porosity;
D O I：
暂无
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Nowadays, with rapid advancement in 3D printing, a relatively low cost 3D for polymer based printers using an open-source self-replicating prototype has increasingly been used in many applications. The printer variants can fabricate any complex parts. In this study, the tensile strength and porosity of PLA and its utilization in 3D printing for standard usage of low cost 3D printers using open- source has been investigated. It was found that, the parts printed from a low cost 3D printer produce relatively acceptable tensile strength and porosity as those from mid-range commercial manufacturer.
引用
收藏
页码：69 / 70
页数：2
相关论文
共 50 条
  • [31] Optimization of Charpy Impact Strength of Tough PLA Samples Produced by 3D Printing Using the Taguchi Method
    Tuncel, Oguz
    POLYMERS, 2024, 16 (04)
  • [32] Evaluation of Printing Parameters on Porosity and Mechanical Properties of 3D Printed PLA/PBAT Blend Parts
    Cardoso, Paulo Henrique Machado
    Coutinho, Rafaella Rabello Teixeira Perdone
    Drummond, Flavia Rocha
    da Conceicao, Marceli do Nascimento
    Thire, Rossana Mara da Silva Moreira
    MACROMOLECULAR SYMPOSIA, 2020, 394 (01)
  • [33] Improving surface roughness of polylactic acid (PLA) products manufactured by 3D printing using a novel slurry impact technique
    Heshmat, Mahmoud
    Abdelrhman, Yasser
    RAPID PROTOTYPING JOURNAL, 2021, 27 (10) : 1791 - 1800
  • [34] Miniaturization of ESPAR Antenna Using Low-Cost 3D Printing Process
    Czelen, M.
    Rzymowski, M.
    Nyka, K.
    Kulas, L.
    2020 14TH EUROPEAN CONFERENCE ON ANTENNAS AND PROPAGATION (EUCAP 2020), 2020,
  • [35] Modeling strength and failure variability due to porosity in additively manufactured metals
    Khalil, M.
    Teichert, G. H.
    Alleman, C.
    Heckman, N. M.
    Jones, R. E.
    Garikipati, K.
    Boyce, B. L.
    COMPUTER METHODS IN APPLIED MECHANICS AND ENGINEERING, 2021, 373
  • [36] Design of 3D Additively Manufactured Hybrid Structures for Cranioplasty
    De Santis, Roberto
    Russo, Teresa
    Rau, Julietta V.
    Papallo, Ida
    Martorelli, Massimo
    Gloria, Antonio
    MATERIALS, 2021, 14 (01) : 1 - 15
  • [37] Influence of 3D printing orientations on physico-mechanical properties and accuracy of additively manufactured dental ceramics
    Alghauli, Mohammed Ahmed
    Almuzaini, Sarah
    Aljohani, Rola
    Alqutaibi, Ahmed Yaseen
    JOURNAL OF PROSTHODONTIC RESEARCH, 2025,
  • [38] Design optimization of PLA lattice in 3D printing
    Jain, R.
    Gupta, N.
    MATERIALS TODAY-PROCEEDINGS, 2022, 59 : 1577 - 1583
  • [39] Hysteresis Measurements and Numerical Losses Segregation of Additively Manufactured Silicon Steel for 3D Printing Electrical Machines
    Tiismus, Hans
    Kallaste, Ants
    Belahcen, Anouar
    Vaimann, Toomas
    Rassolkin, Anton
    Lukichev, Dmitry
    APPLIED SCIENCES-BASEL, 2020, 10 (18):
  • [40] Process optimisation on the compressive strength property for the 3D printing of PLA/almond shell composite
    Veeman, Dhinakaran
    Palaniyappan, Sabarinathan
    JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS, 2023, 36 (06) : 2435 - 2458
12345