Mechanical characterization of inkjet 3D printed microcantilevers

被引：0
|
作者：
Kawa, Bartosz [1 ]
Adamski, Krzysztof [1 ]
Lizanets, Danylo [1 ]
Walczak, Rafal [1 ]
机构：
[1] Wroclaw Univ Sci & Technol, Fac Microsyst Elect & Photon, Janiszewski Str 11-17, PL-50372 Wroclaw, Poland
来源：
2018 XV INTERNATIONAL SCIENTIFIC CONFERENCE ON OPTOELECTRONIC AND ELECTRONIC SENSORS (COE) | 2018年
关键词：
microcantilevers; inkjet 3D printing; mechanical characterization; sensor; actuartor;
D O I：
暂无
中图分类号：
TM [电工技术]; TN [电子技术、通信技术];
学科分类号：
0808 ; 0809 ;
摘要：
The paper presents results of characterization of inkjet 3D printed microcantilevers. Determination of mechanical properties of microstructures is a key issue towards application of the structures in the 3D printed sensors or actuators. Micro cantilevers with different length and thicknesses were designed, printed and characterized. Obtained results were compared to the computer simulations. Knowledge on the mechanical properties of 3D printed microcantilevers will allow to predict and evaluate the behavior of future designed structures applied in microsensors, microactuators.
引用
收藏
页数：3
相关论文
共 50 条
  • [41] Microstructural characterization of 3D printed concrete
    Yu, Shiwei
    Xia, Ming
    Sanjayan, Jay
    Yang, Lin
    Xiao, Jianzhuang
    Du, Hongjian
    JOURNAL OF BUILDING ENGINEERING, 2021, 44
  • [42] 3D Inkjet Printed Disposable Environmental Monitoring Wireless Sensor Node
    Farooqui, Muhammad Fahad
    Shamim, Atif
    2017 IEEE MTT-S INTERNATIONAL MICROWAVE SYMPOSIUM (IMS), 2017, : 1375 - 1378
  • [43] Mechanical characterization of 3D printed continuous carbon fiber reinforced thermoplastic composites
    Li, Lijun
    Liu, Wenyao
    Sun, Lingyu
    COMPOSITES SCIENCE AND TECHNOLOGY, 2022, 227
  • [44] A MEMS dynamic mechanical analyzer for in situ viscoelastic characterization of 3D printed nanostructures
    Cayll, David R.
    Ladner, Ian S.
    Cho, Joon Hyong
    Saha, Sourabh K.
    Cullinan, Michael A.
    JOURNAL OF MICROMECHANICS AND MICROENGINEERING, 2020, 30 (07)
  • [45] Electrical and mechanical characterization of inkjet-printed functional structures
    Beisteiner, Christoph
    Gstoettenmayr, Richard
    Altmanninger, Thomas
    Zagar, Bernhard G.
    TM-TECHNISCHES MESSEN, 2016, 83 (11) : 647 - 659
  • [46] Inkjet Printed GPS Antenna on a 3D Printed Substrate using Low-Cost Machines
    Heirons, J.
    Jun, S.
    Shastri, A.
    Sanz-Izquierdo, B.
    Bird, David
    Winchester, L.
    Evans, L.
    McClelland, A.
    2016 LOUGHBOROUGH ANTENNAS & PROPAGATION CONFERENCE (LAPC), 2016,
  • [47] Interfacial mechanical behavior of 3D printed ABS
    Cole, Daniel P.
    Riddick, Jaret C.
    Jaim, H. M. Iftekhar
    Strawhecker, Kenneth E.
    Zander, Nicole E.
    JOURNAL OF APPLIED POLYMER SCIENCE, 2016, 133 (30)
  • [48] Buildability and Mechanical Properties of 3D Printed Concrete
    Joh, Changbin
    Lee, Jungwoo
    Bui, The Quang
    Park, Jihun
    Yang, In-Hwan
    MATERIALS, 2020, 13 (21) : 1 - 24
  • [49] Mechanical and Thermal Properties of 3D Printed Polycarbonate
    Bahar, Anis
    Belhabib, Sofiane
    Guessasma, Sofiane
    Benmahiddine, Ferhat
    Hamami, Ameur El Amine
    Belarbi, Rafik
    ENERGIES, 2022, 15 (10)
  • [50] Mechanical Characteristics of 3D Printed Airway Stent
    Wood, C.
    Cheng, G.
    Miller, A.
    Wahidi, M. M.
    Gall, K.
    AMERICAN JOURNAL OF RESPIRATORY AND CRITICAL CARE MEDICINE, 2018, 197
12345