Modelling and simulation of die casting process for A356 semi-solid alloy

被引：9

作者：

Fu, Jinlong ^{[1
]}

Wang, Kaikun ^{[1
]}

机构：

[1] Univ Sci & Technol Beijing, Sch Mat Sci & Engn, Beijing 100083, Peoples R China

来源：

11TH INTERNATIONAL CONFERENCE ON TECHNOLOGY OF PLASTICITY, ICTP 2014 | 2014年 / 81卷

关键词：

One-phase model; Constitutive equation; Isothermal experiment; Die filling simulation; METAL-ALLOYS; BEHAVIOR; STATE;

D O I：

10.1016/j.proeng.2014.10.191

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

To describe the flow behaviors of semi-solid state alloy A356, two non-Newtonian constitutive equations are modeled in this paper. All the parameters in the above equations are obtained by an isothermal shear experiment. The CFD software PROCAST is used to simulate the process of die filling. The filling temperature is 585 degrees C (solid fraction is 0.4). A Newtonian type fluid which stands for the traditional casting is also performed. Based on the results of the simulation, it is found that the material in semi-solid state exhibits an apparently higher viscosity and thus, flows much more smoothly than the Newtonian fluid. In addition, the semi-solid metal alloy has a special die filling behavior compared with liquid filling which is of great importance in improving the quality of the final components. (C) 2014 Published by Elsevier Ltd.

引用

页码：1565 / 1570

页数：6

共 50 条

[41] Precipitation hardening of A356 Al alloy produced by gas induced semi-solid process
Wisutmethangoon, S.
Thongjan, S.
Mahathaninwong, N.
Plookphol, T.
Wannasin, J.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 532 : 610 - 615
[42] Significant improvement of semi-solid microstructure and mechanical properties of A356 alloy by ARB process
Jamaati, Roohollah
Amirkhanlou, Sajjad
Toroghinejad, Mohammad Reza
Niroumand, Behzad
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (06): : 2495 - 2501
[43] Numerical simulation of semi-solid die-casting process of automobile aluminum alloy part
Wang, Jiao-Jiao
Shang, Shu-Zhen
Lu, Gui-Min
Zhang, Wan-Ning
Tang, Xiao-Ling
Yu, Jian-Guo
Zhongguo Youse Jinshu Xuebao/Chinese Journal of Nonferrous Metals, 2012, 22 (04): : 1045 - 1052
[44] Investigation of Thin Wall Casting Made of Semi-Solid A356 Using Back Extrusion and Die Cast
Moradi, M.
Nili-Ahmadabadi, M.
Heidarian, B.
Ashouri, S.
SEMI-SOLID PROCESSING OF ALLOYS AND COMPOSITES X, 2008, 141-143 : 67 - 72
[45] Effects of Solid–Liquid Mixing on Microstructure of Semi-Solid A356 Aluminum Alloy
H. M. Guo
L. J. Wang
Q. Wang
X. J. Yang
Metallurgical and Materials Transactions B, 2014, 45 : 1490 - 1495
[46] Semi-solid A356 Al-alloy slurry prepared by serpentine pipe with multiple curves casting
Chen, Zheng-Zhou
Mao, Wei-Min
Wu, Zong-Chuang
Zhongguo Youse Jinshu Xuebao/Chinese Journal of Nonferrous Metals, 2011, 21 (01): : 95 - 101
[47] Development of Microstructure of Semi-Solid A356 Alloy by Alternating Electromagnetic Stirring
Liu, Wen
Li, Jiqiang
Ding, Xu
CHINA POSTDOCTORAL FORUM ON MATERIALS SCIENCE AND ENGINEERING, 2011, 266 : 84 - 88
[48] Die Filling Behaviour of Semi Solid A356 Al Alloy Slurry During Rheo Pressure Die Casting
Prosenjit Das
Sudip K. Samanta
Shashank Tiwari
Pradip Dutta
Transactions of the Indian Institute of Metals, 2015, 68 : 1215 - 1220
[49] Experimental characterisation of a semi-solid A356 alloy during solidification and remelting
Dziallach, S.
Benke, S.
Prahl, U.
Bleck, W.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH, 2009, 22 (1-4) : 248 - 251
[50] Behavior of A356 Alloy in semi-solid state produced by mechanical stirring
Nourouzi, Salman
Kolahdooz, Amin
Botkan, Mohammad
ADVANCES IN METALLURGICAL AND MINING ENGINEERING, 2012, 402 : 331 - 336

← 1 2 3 4 5 →