INVESTIGATIONS OF THE SHRINK-FITTED JOINTS IN ASSEMBLED CRANKSHAFTS

被引：0

作者：

Siemiatkowski, Zbigniew ^{[1
]}

Rucki, Miroslaw ^{[1
]}

Lavrynenko, Sergiy ^{[2
]}

机构：

[1] Kazimierz Pulaski Univ Technol & Humanities Radom, Radom, Poland

[2] Natl Tech Univ, Kharkov Polytech Inst, Kharkov, Ukraine

来源：

PROCEEDINGS OF THE 7TH INTERNATIONAL CONFERENCE ON MECHANICS AND MATERIALS IN DESIGN (M2D2017) | 2017年

关键词：

mechanical engineering; shrink fittings; assembled crankshafts;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This work describes the investigations on the shrink-fitted joints. The models of the marine engine cranks and pivots were made in the scale 1: 5 considering the real manufacturing conditions of the large-sized crankshafts. The results of the ultrasonic measurements of the stresses were compared to the temperature distribution during the cooling of the assembled couplings. The conclusion was that the unsteady stress distribution might be caused by the unsteady cooling process. As a consequence, more tight joints may reveal not better ability to bear a load torque.

引用

页码：1155 / 1158

页数：4

共 50 条

[31] Analytical Modeling of Shrink-Fitted FGM Thick-Walled Cylinders
Zrinej, Samiha
Laghzale, Noreddine
Bouzid, Hakim A.
INTERNATIONAL JOURNAL OF ENGINEERING RESEARCH IN AFRICA, 2023, 66 : 61 - 74
[32] Simulations of interfacial creep generation for shrink-fitted bimetallic work roll
Sakai, H.
Noda, N-A
Sano, Y.
Takase, Y.
Zhang, G. W.
2018 INTERNATIONAL CONFERENCE ON MATERIAL STRENGTH AND APPLIED MECHANICS (MSAM 2018), 2018, 372
[33] Torsional fretting fatigue strength of a shrink-fitted shaft with a grooved hub
Juuma, T
TRIBOLOGY INTERNATIONAL, 2000, 33 (08) : 537 - 543
[34] Photoelastic investigation of friction and residual stress in shrink-fitted shafts and hubs
Jones, IA
Truman, CE
Booker, JD
ADVANCES IN EXPERIMENTAL MECHANICS, 2004, 1-2 : 171 - 176
[35] EFFECT OF CORROSIVE ENVIRONMENT ON FATIGUE STRENGTH OF SHRINK-FITTED AXLE.
Gotoh, Yoshiki
Ohuchida, Hisashi
Zairyo/Journal of the Society of Materials Science, Japan, 1986, 35 (394) : 797 - 803
[36] Axisymmetric stress analysis and strength of bonded shrink-fitted joints subjected to push-off forces and torsional loads
Sawa, T
Yoneno, M
Shimotakahara, K
Motegi, Y
ADHESIVE JOINTS: FORMATION, CHARACTERISTICS AND TESTING, VOL 2, 2002, : 273 - 297
[37] Axisymmetric stress analysis and strength of bonded shrink-fitted joints of solid shafts subjected to push-off forces
Yoneno, Masahiro
Sawa, Toshiyuki
Shimotakahara, Ken
Motegi, Yoichi
1997, JSME, Tokyo, Japan (63):
[38] Effect of Driving Torque on the Interfacial Creep for Shrink-fitted Bimetallic Work Roll
Sakai, Hiromasa
Noda, Nao-Aki
Sano, Yoshikazu
Zhang, Guowei
Takase, Yasushi
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2019, 105 (12): : 1126 - 1134
[39] A simple method of analysis of partial slip in shrink-fitted shafts under torsion
Bertocchi, E.
Mantovani, S.
Ciavarella, M.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2018, 142 : 541 - 546
[40] The fretting fatigue strength of a shrink-fitted shaft in contact with various hub materials
Juuma, T
SYSTEMS INTEGRITY AND MAINTENANCE, PROCEEDINGS, 2000, : 224 - 229

← 1 2 3 4 5 →