Deep hole drilling using tools with small diameters-Process analysis and process design

被引：37

作者：

Zabel, Andreas ^{[1
]}

Heilmann, Markus ^{[1
]}

机构：

[1] TU Dortmund Univ, Inst Machining Technol, Dortmund, Germany

来源：

CIRP ANNALS-MANUFACTURING TECHNOLOGY | 2012年 / 61卷 / 01期

关键词：

Drilling; Tool geometry; Laser;

D O I：

10.1016/j.cirp.2012.03.002

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This paper is focused on the drilling of bore holes with high length-to-diameter ratios and diameters less than 2 mm which are needed, for example, in medical and automotive applications. In the presented research, the influence of cutting data and tool design on tool wear and chip formation has been analysed. First the experimental set-up is described followed by an in-depth process analysis of the single-lip deep hole drilling process under investigation. The next section deals with a process combination, where laser and mechanical drilling are combined in order to improve process reliability and productivity. (C) 2012 CIRP.

引用

页码：111 / 114

页数：4

共 50 条

[41] Using virtual tools for Quenching process design
2018, ASM International (176):
[42] USING VIRTUAL TOOLS FOR QUENCHING PROCESS DESIGN
Jan, James
Nannapuraju, Madhusudhan
ADVANCED MATERIALS & PROCESSES, 2018, 176 (04): : 38 - 42
[43] Current developments of tool- and process designing in deep drilling Analysis and optimisation of deep drilling process under consideration of current trends
Biermann, Dirk
Felderhoff, F.
Heilmann, M.
Kersting, M.
Kessler, N.
Sacharow, A.
PRAZISIONS- UND TIEFBOHREN AKTUELL: TECHNIK - TOOLS - TRENDS, 2008, 2054 : 141 - 154
[44] Laser hole drilling process studied using laser speckle correlation
Sjodahl, Mikael
Gren, Per
Sarady, Istvan
Miroshnicova, Natalia
SPECKLE06: SPECKLES, FROM GRAINS TO FLOWERS, 2006, 6341
[45] Evaluation of Residual Stress in the Hot Forming Process Using Hole Drilling
Azizpour, M. Jalali
Fattahi, Hamed
RESIDUAL STRESSES 2016: ICRS-10, 2017, 2 : 121 - 126
[46] TOOLS FOR PROCESS DESIGN
FRIEND, L
CHEMICAL ENGINEERING PROGRESS, 1948, 44 (03) : 253 - 256
[47] The Effect of Optical System Design for Laser Micro-hole Drilling Process
Ding, Chien-Fang
Lan, Yin-Te
Chien, Yu-Lun
Young, Hong-Tsu
CURRENT DEVELOPMENTS IN LENS DESIGN AND OPTICAL ENGINEERING XVIII, 2017, 10375
[48] Improving Machining Performance for Deep Hole Drilling in the Electrical Discharge Machining Process Using a Step Cylindrical Electrode
Jamkamon, Kamonpong
Janmanee, Pichai
APPLIED SCIENCES-BASEL, 2021, 11 (05): : 1 - 15
[49] Development and analysis of a mechatronic system for in-process monitoring and compensation of straightness deviation in BTA deep hole drilling
Gerken, Julian Frederic
Klages, Niklas
Biermann, Dirk
Denkena, Berend
MECHANICAL SYSTEMS AND SIGNAL PROCESSING, 2022, 170
[50] A countermeasure against a rifling mark generating phenomenon on BTA deep hole drilling process
Matsuzaki K.
Sueoka A.
Ryu T.
Morita H.
Nihon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C, 2010, 76 (767): : 1684 - 1691

← 1 2 3 4 5 →