A countermeasure against a rifling mark generating phenomenon on BTA deep hole drilling process

被引：0
|
作者：
Matsuzaki K. [1 ]
Sueoka A. [1 ]
Ryu T. [1 ]
Morita H. [1 ]
机构：
[1] Department of Mechanical Engineering, Kyushu University, Nishi-ku, Fukuoka-shi, Fukuoka, 819-0395
来源：
Nihon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C | 2010年 / 76卷 / 767期
关键词：
Chatter vibration; Drilling; Pattern formation; Rifling mark; Self-Excited vibration; Stability; Vibration of rotating body;
D O I：
10.1299/kikaic.76.1684
中图分类号：
学科分类号：
摘要：
BTA deep hole drilling is used for producing holes of high aspect ratio. In this process, a chatter vibration sometimes occurs and a rifling mark is formed on the surface of the hole. The generating mechanism of the rifling mark in BTA deep hole drilling process has been studied as a self-excited vibration caused by time delay. In this paper, a BTA machining head which has two guide pads is treated, and countermeasures against the generation of rifling mark phenomenon are considered. The influence of the locations of the guide pads is analyzed. Also, the preventing method by an additional guide pad is proposed, and the effect of the preventing method is investigated. Furthermore, the optimal location of the guide pads is studied by quasi-static analysis. According to the numerical result, it was confirmed that the perfect prevention of the generation of rifling mark phenomenon was possible by using an additional guide pad and locating the guide pads appropriately.
引用
收藏
页码：1684 / 1691
页数：7
相关论文
共 50 条
  • [1] Experimental study for a countermeasure against rifling mark generating phenomena on BTA deep hole drilling process
    Ryu, T.
    Matsuzaki, K.
    Tsukamoto, K.
    Fujii, K.
    Yuge, Y.
    Nakao, S.
    Honda, T.
    Sueoka, A.
    PROCEEDINGS OF INTERNATIONAL CONFERENCE ON NOISE AND VIBRATION ENGINEERING (ISMA2012) / INTERNATIONAL CONFERENCE ON UNCERTAINTY IN STRUCTURAL DYNAMICS (USD2012), 2012, : 3071 - 3082
  • [2] Theoretical and experimental study on rifling mark generating phenomena in BTA deep hole drilling process (generating mechanism and countermeasure)
    Matsuzaki, Kenichiro
    Ryu, Takahiro
    Sueoka, Atsuo
    Tsukamoto, Keizo
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2015, 88 : 194 - 205
  • [3] Numerical study for rifling mark generating phenomena on BTA deep hole drilling process
    Matsuzaki, K.
    Ryu, T.
    Sueoka, A.
    Tsukamoto, K.
    Honda, T.
    PROCEEDINGS OF INTERNATIONAL CONFERENCE ON NOISE AND VIBRATION ENGINEERING (ISMA2012) / INTERNATIONAL CONFERENCE ON UNCERTAINTY IN STRUCTURAL DYNAMICS (USD2012), 2012, : 3033 - 3046
  • [4] Study for generation mechanism of a rifling mark on bta deep hole drilling process
    Matsuzaki, Kenichiro
    Sueoka, Atsuo
    Ryu, Takahiro
    Morita, Hidetoshi
    Nihon Kikai Gakkai Ronbunshu, C Hen/Transactions of the Japan Society of Mechanical Engineers, Part C, 2009, 75 (755): : 1918 - 1925
  • [5] Simulation of the BTA deep-hole drilling process
    Biermann D.
    Sacharow A.
    Wohlgemuth K.
    Prod. Eng., 2009, 4-5 (339-346): : 339 - 346
  • [6] The investigation on the machining process of BTA deep hole drilling
    Gao, CH
    Cheng, K
    Kirkwood, D
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2000, 107 (1-3) : 222 - 227
  • [7] Roundness modeling in BTA deep hole drilling
    Chin, DH
    Yoon, MC
    Sim, SB
    PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY, 2005, 29 (02): : 176 - 188
  • [8] Application and use of multivariate control charts in a BTA deep hole drilling process
    Messaoud, A
    Theis, W
    Weihs, C
    Hering, F
    Classification - the Ubiquitous Challenge, 2005, : 648 - 655
  • [9] The shaft behavior of BTA deep hole drilling tool
    Chin, JH
    Hsieh, CT
    Lee, LW
    INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 1996, 38 (05) : 461 - 482
  • [10] Eigensolution of a BTA deep-hole drilling shaft system
    Ma, Guo-hong
    Shen, Xing-quan
    JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY, 2018, 32 (04) : 1499 - 1504
12345