The Preliminary Study Of Machinability During Milling Of Titanium Alloy (Ti-6Al-4V)

被引：0
|
作者：
Serboi, Claudia [1 ]
Velicu, Stefan [1 ]
Darnis, Philippe [2 ]
Laheurte, Raynald [2 ]
Ionescu, Cristian [3 ]
机构：
[1] Univ Politehn Bucuresti, Bucharest, Romania
[2] Univ Bordeaux 1, F-33405 Talence, France
[3] SC HESPER SA, Bucharest, Romania
来源：
OPTIMIZATION OF THE MECHANICAL ENGINEERING, MANUFACTURING SYSTEMS, ROBOTICS AND AEROSPACE | 2012年 / 186卷
关键词：
titanium alloys; machinability; cutting forces; machining parameters;
D O I：
10.4028/www.scientific.net/AMM.186.200
中图分类号：
V [航空、航天];
学科分类号：
08 ; 0825 ;
摘要：
Titanium and its alloys have found wide application in the aerospace, biomedical and automotive industries owing to their good strength-to weight ratio and high corrosion resistance. However, these alloys have very poor machinability, which is attributed to their inherent high strength maintained at elevated temperature and low thermal conductivity leading to high cutting temperatures. This paper presents the findings of an experimental investigation into the effects of cutting speed, feed rate and depth of cut when milling titanium alloy Ti-6Al-4V. The cutting forces were the response variables investigated. This experimental investigation is translated into a mathematical model of cutting forces designed on the basis of the results obtained from this research.
引用
收藏
页码：200 / +
页数：2
相关论文
共 50 条
  • [21] Machinability study in milling of Ti-6Al-4V using cryogenic treated and coated tool
    Anthuvan, R. Naveen
    Kumar, S. Pratheesh
    Prakash, R. Arun
    Arunkarthik, B.
    Akhilesh, A.
    MATERIALS TODAY-PROCEEDINGS, 2021, 46 : 8417 - 8428
  • [22] A study of the machinability of Ti-6Al-4V compacted powders
    Tambani, M. T.
    Machio, C.
    Madyira, D. M.
    Uheida, E. H.
    Oosthuizen, G. A.
    CONFERENCE OF THE SOUTH AFRICAN ADVANCED MATERIALS INITIATIVE (COSAAMI-2018), 2018, 430
  • [23] MACHINABILITY STUDIES OF WROUGHT TITANIUM ALLOY Ti-6Al-4V BASED ON ORTHOGONAL ARRAY DESIGN
    Rajan, K. M.
    Kumar Sahoo, Ashok
    Routara, Bharat Chandra
    Panda, Amlana
    Kumar, Ramanuj
    SURFACE REVIEW AND LETTERS, 2023, 30 (03)
  • [24] Machinability and tribological investigation of nano-hybrid cryogenic-MQL during milling Ti-6Al-4V alloy
    Hadi, Musfirah Abdul
    JURNAL TRIBOLOGI, 2025, 44 : 67 - 82
  • [25] Surface integrity in high speed end milling of titanium alloy Ti-6Al-4V
    Daymi, A.
    Boujelbene, M.
    Ben Amara, A.
    Bayraktar, E.
    Katundi, D.
    MATERIALS SCIENCE AND TECHNOLOGY, 2011, 27 (01) : 387 - 394
  • [26] Simulation of The High-speed Milling Temperature of Titanium Alloy Ti-6Al-4V
    Huang, Xinchun
    Yao, Changfeng
    Zhang, Dinghua
    Ren, Junxue
    ADVANCED MANUFACTURING TECHNOLOGY, PTS 1-3, 2011, 314-316 : 1171 - 1175
  • [27] MILLING FORCE AND SURFACE TOPOGRAPHY OF Ti-6Al-4V TITANIUM ALLOY CLADDED BY THE LASER
    Wang, Tao
    Li, Yang
    Liu, Jiaqi
    Qin, Lingchao
    Wang, Ning
    Zhang, Lifeng
    Wang, Hao
    Li, Zhan
    SURFACE REVIEW AND LETTERS, 2019, 26 (05)
  • [28] Modeling Cutting Force in Micro-Milling of Ti-6Al-4V Titanium Alloy
    Pratap, Tej
    Patra, Karali
    Dyakonov, A. A.
    INTERNATIONAL CONFERENCE ON INDUSTRIAL ENGINEERING (ICIE-2015), 2015, 129 : 134 - 139
  • [29] Formation of titanium hydride in Ti-6Al-4V alloy
    Luo, Liangshun
    Su, Yanqing
    Guo, Jingjie
    Fu, Hengzhi
    JOURNAL OF ALLOYS AND COMPOUNDS, 2006, 425 (1-2) : 140 - 144
  • [30] Elastic properties of the titanium alloy Ti-6Al-4V
    Trofimov, E. A.
    Lutfullin, R. Ya.
    Kashaev, R. M.
    LETTERS ON MATERIALS-PIS MA O MATERIALAKH, 2015, 5 (01): : 67 - 69
12345