Application of Taguchi Method for Surface Roughness and Roundness Error in Drilling of AISI 316 Stainless Steel

被引：44

作者：

Cicek, Adem ^{[2
]}

Kivak, Turgay ^{[1
]}

Samtas, Gurcan ^{[1
]}

机构：

[1] Duzce Univ, Cumayeri Vocat Sch Higher Educ, TR-81700 Cumayeri, Duzce, Turkey

[2] Duzce Univ, Fac Technol, Dept Mfg Engn, Duzce, Turkey

来源：

STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING | 2012年 / 58卷 / 03期

关键词：

cryogenic treatment; drilling; surface roughness; roundness error; Taguchi method; MACHINING PARAMETERS; CUTTING PARAMETERS; TOOL WEAR; OPTIMIZATION; DEVIATION; FORCE;

D O I：

10.5545/sv-jme.2011.167

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

In this study, the effects of deep cryogenic treatment and drilling parameters on surface roughness and roundness error were investigated in drilling of AISI 316 austenitic stainless steel with M35 HSS twist drills. In addition, optimal control factors for the hole quality were determined by using Taguchi technique. Two cutting tools, cutting speeds and feed rates were considered as control factors, and L-8(2(3)) orthogonal array was determined for experimental trials. Multiple regression analysis was employed to derive the predictive equations of the surface roughness and roundness error achieved via experimental design. Minimum surface roughness and roundness error were obtained with treated drills at 14 m/min cutting speed and 0.08 mm/rev feed rate. Confirmation experiments showed that Taguchi method precisely optimized the drilling parameters in drilling of stainless steel.

引用

页码：165 / 174

页数：10

共 50 条

[1] Application of taguchi method for surface roughness and roundness error in drilling of AISI 316 stainless steel
Düzce University, Faculty of Technology, Department of Manufacturing Engineering, Düzce, Turkey
不详
Stroj Vest, 3 (165-174):
[2] Optimization of flank wear and surface roughness during turning of AISI 304 stainless steel using the Taguchi method
Ozbek, Nursel Altan
Karadag, Metin Ibrahim
Ozbek, Onur
MATERIALS TESTING, 2020, 62 (09) : 957 - 961
[3] OPTIMIZATION OF SURFACE ROUGHNESS OF AISI 304 AUSTENITIC STAINLESS STEEL IN DRY TURNING OPERATION USING TAGUCHI DESIGN METHOD
Selvaraj, D. Philip
Chandramohan, P.
JOURNAL OF ENGINEERING SCIENCE AND TECHNOLOGY, 2010, 5 (03) : 293 - 301
[4] Electrolyte Effect on the Surface Roughness Obtained by Electropolishing of AISI 316L Stainless Steel
Nunez Lopez, P. J.
Garcia Plaza, E.
Hernando Prada, M.
Trujillo Coronel, R.
ADVANCES IN MATERIALS PROCESSING TECHNOLOGIES-MESIC V, 2014, 797 : 133 - 138
[5] Optimizing surface roughness of workpieces made of stainless steel 316L with DMLS technology: a Taguchi method approach
Jakupi, Kaltrine
Dukovski, Vladimir
Abdullahu, Fitore
ENGINEERING RESEARCH EXPRESS, 2024, 6 (02):
[6] Prediction of surface roughness in low speed turning of AISI316 austenitic stainless steel
Assis Acayaba, Gabriel Medrado
de Escalona, Patricia Munoz
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2015, 11 : 62 - 67
[7] Analysis of roundness error and surface roughness in the electro jet drilling process
Sen, M
Shan, HS
MATERIALS AND MANUFACTURING PROCESSES, 2006, 21 (01) : 1 - 9
[8] Studies on Electron Beam Surface Melting of AISI 316 Stainless Steel and AISI 347 Stainless Steel
Basak, Soumyabrata
Sahu, Kisor K.
Sharm, Sumit K.
Majumdar, J. Dutta
INTERNATIONAL CONFERENCE ON SUSTAINABLE MATERIALS PROCESSING AND MANUFACTURING (SMPM 2017), 2016, 7 : 647 - 653
[9] Investigation on dissimilar welding of AISI 409 ferritic stainless steel to AISI 316L austenitic stainless steel by using grey based Taguchi method
Ghosh, Nabendu
Pal, Pradip Kumar
Nandi, Goutam
ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2018, 4 (03) : 385 - 401
[10] Taguchi method based optimisation of drilling parameters in drilling of AISI 316 steel with PVD monolayer and multilayer coated HSS drills
Kivak, Turgay
Samtas, Gurcan
Cicek, Adem
MEASUREMENT, 2012, 45 (06) : 1547 - 1557

← 1 2 3 4 5 →