Optimization of Performance Parameters of Phase Frequency Detector Using Taguchi DoE and Pareto ANOVA Techniques

被引:4
|
作者
Sharma, Jyoti [1 ]
Sharma, Gaurav Kumar [2 ]
Varma, Tarun [3 ]
Boolchandani, Dharmendar [3 ]
机构
[1] Malaviya Natl Inst Technol, Birla Inst Technol, ECE Dept, Jaipur 302017, Rajasthan, India
[2] GLA Univ, ECE Dept, Mathura 281406, Uttar Pradesh, India
[3] Malaviya Natl Inst Technol, ECE Dept, Jaipur 302017, Rajasthan, India
关键词
Phase frequency detector (PFD); optimization; Taguchi DoE; Pareto ANOVA; maximum operating frequency; phase noise; power dissipation; Cadence; Minitab software; MINIMAL BLIND ZONE; PLL; DESIGN; PFD;
D O I
10.1142/S021812662350158X
中图分类号
TP3 [计算技术、计算机技术];
学科分类号
0812 ;
摘要
This paper utilizes Taguchi design of experiments and Pareto analysis of variance statistical approaches to demonstrate circuit optimization. The phase-frequency detector (PFD) circuit based on dynamic logic has been chosen for optimization. For various MOSFETs of PFD, three levels and three factors of power supply and width of PMOS and NMOS (V-DD, w(p), and w(n)) are considered to be critical performance governing factors. The Taguchi technique determines the level of significance of a factor that influences a given performance parameter. The crucial factor for a given response is determined via ANOVA analysis. The optimum values for the parameters V-DD, w(p), and w(n )are likewise determined using this procedure to maximize the circuit's overall performance. Taguchi DoE and Pareto Anova analyses have been performed using the Minitab software. Simulating the circuit with GPDK 180nm CMOS technology using these methods ensures that the acquired parameters are correct for best performance. The Cadence Virtuoso tool has been used to conduct pre-layout and post-layout simulations. The simulation outcomes are reasonably close to the ANOVA predicted result. Phase noise, power dissipation, and frequency of operation of the proposed PFD are -159.56dBc/Hz, 9.83 mu W, and 10.21GHz, respectively, and it occupies a chip area of 300.41 mu m(2). The proposed PFD is used to implement a charge-pump PLL which performs effectively with a settling time of 2.59 mu s.
引用
收藏
页数:19
相关论文
共 50 条
  • [21] Modelling of extrusion process and application of Taguchi method and ANOVA analysis for optimization the parameters
    Hosseini, A.
    Farhangdoost, Kh.
    Manoochehri, M.
    MECHANIKA, 2012, (03): : 301 - 305
  • [22] Parameters Optimization in Manufacturing Nanopowder Bioceramics of Eggshell with Pulverisette 6 Machine using Taguchi and ANOVA Method
    Van Hoten, H.
    Gunawarman
    Mulyadi, I. Hari
    Mainil, A. Kurniawan
    Bismantolo, P.
    Nurbaiti
    INTERNATIONAL JOURNAL OF ENGINEERING, 2018, 31 (01): : 45 - 49
  • [23] APPLICATION OF TAGUCHI AND ANOVA IN OPTIMIZATION OF PROCESS PARAMETERS OF LAPPING OPERATION FOR CAST IRON
    Parate, P. R.
    Yarasu, R. B.
    JOURNAL OF MECHANICAL ENGINEERING AND SCIENCES, 2013, 4 : 479 - 487
  • [24] OPTIMIZATION OF PROCESS PARAMETERS DURING DRILLING OF GLASS-FIBER POLYESTER REINFORCED COMPOSITES USING DOE AND ANOVA
    Mohan, N. S.
    Kulkarni, S. M.
    Ramachandra, A.
    IIUM ENGINEERING JOURNAL, 2006, 7 (01): : 13 - 24
  • [25] Application of DOE and ANOVA in Optimization of HVOF Spraying Parameters in the Development of New Ti Coatings
    N. Pulido-González
    S. García-Rodríguez
    M. Campo
    J. Rams
    B. Torres
    Journal of Thermal Spray Technology, 2020, 29 : 384 - 399
  • [26] Application of DOE and ANOVA in Optimization of HVOF Spraying Parameters in the Development of New Ti Coatings
    Pulido-Gonzalez, N.
    Garcia-Rodriguez, S.
    Campo, M.
    Rams, J.
    Torres, B.
    JOURNAL OF THERMAL SPRAY TECHNOLOGY, 2020, 29 (03) : 384 - 399
  • [27] Optimization of electrospinning process parameters to develop the smallest ZnO + PVP nanofibres using Taguchi experimental design and ANOVA
    Harshada Vishal Mhetre
    Kanse Yuvraj Krishnarao
    Nithesh Naik
    Journal of Materials Science: Materials in Electronics, 2023, 34
  • [28] Performance optimization and parametric evaluation of the cascade vapor compression refrigeration cycle using Taguchi and ANOVA methods
    Ustaoglu, Abid
    Kursuncu, Bilal
    Alptekin, Mustafa
    Gok, M. Sabri
    APPLIED THERMAL ENGINEERING, 2020, 180
  • [29] Optimization of Machining Parameters Using the Taguchi and ANOVA Analysis in the Face Milling of Aluminum Alloys AL7075
    Savkovic, Borislav
    Kovac, Pavel
    Stoic, Antun
    Dudic, Branislav
    TEHNICKI VJESNIK-TECHNICAL GAZETTE, 2020, 27 (04): : 1221 - 1228
  • [30] Optimization of Processing Parameters for Shell Products Based on Taguchi Method and DOE Technology
    Li, Chunbo
    Fu, Xuelong
    COMPUTER-AIDED DESIGN, MANUFACTURING, MODELING AND SIMULATION, PTS 1-2, 2011, 88-89 : 274 - +