Optimization of Performance Parameters of Phase Frequency Detector Using Taguchi DoE and Pareto ANOVA Techniques

被引:4
|
作者
Sharma, Jyoti [1 ]
Sharma, Gaurav Kumar [2 ]
Varma, Tarun [3 ]
Boolchandani, Dharmendar [3 ]
机构
[1] Malaviya Natl Inst Technol, Birla Inst Technol, ECE Dept, Jaipur 302017, Rajasthan, India
[2] GLA Univ, ECE Dept, Mathura 281406, Uttar Pradesh, India
[3] Malaviya Natl Inst Technol, ECE Dept, Jaipur 302017, Rajasthan, India
关键词
Phase frequency detector (PFD); optimization; Taguchi DoE; Pareto ANOVA; maximum operating frequency; phase noise; power dissipation; Cadence; Minitab software; MINIMAL BLIND ZONE; PLL; DESIGN; PFD;
D O I
10.1142/S021812662350158X
中图分类号
TP3 [计算技术、计算机技术];
学科分类号
0812 ;
摘要
This paper utilizes Taguchi design of experiments and Pareto analysis of variance statistical approaches to demonstrate circuit optimization. The phase-frequency detector (PFD) circuit based on dynamic logic has been chosen for optimization. For various MOSFETs of PFD, three levels and three factors of power supply and width of PMOS and NMOS (V-DD, w(p), and w(n)) are considered to be critical performance governing factors. The Taguchi technique determines the level of significance of a factor that influences a given performance parameter. The crucial factor for a given response is determined via ANOVA analysis. The optimum values for the parameters V-DD, w(p), and w(n )are likewise determined using this procedure to maximize the circuit's overall performance. Taguchi DoE and Pareto Anova analyses have been performed using the Minitab software. Simulating the circuit with GPDK 180nm CMOS technology using these methods ensures that the acquired parameters are correct for best performance. The Cadence Virtuoso tool has been used to conduct pre-layout and post-layout simulations. The simulation outcomes are reasonably close to the ANOVA predicted result. Phase noise, power dissipation, and frequency of operation of the proposed PFD are -159.56dBc/Hz, 9.83 mu W, and 10.21GHz, respectively, and it occupies a chip area of 300.41 mu m(2). The proposed PFD is used to implement a charge-pump PLL which performs effectively with a settling time of 2.59 mu s.
引用
收藏
页数:19
相关论文
共 50 条
  • [1] Parameters Optimization for Electropolishing Titanium by Using Taguchi-Based Pareto ANOVA
    Prihandana, Gunawan Setia
    Sriani, Tutik
    Jamaludin, Mohd Fadzil
    Yusof, Farazila
    Arifvianto, Budi
    Mahardika, Muslim
    METALS, 2023, 13 (02)
  • [2] Design and optimization of phase frequency detector through Taguchi and ANOVA statistical techniques for fast settling low power frequency synthesizer
    Sharma, Jyoti
    Ahmad, Riyaz
    Yadav, Ashutosh
    Varma, Tarun
    Boolchandani, Dharmendar
    INTEGRATION-THE VLSI JOURNAL, 2024, 96
  • [3] Optimization of segmented thermoelectric generator using Taguchi and ANOVA techniques
    Kishore, Ravi Anant
    Sanghadasa, Mohan
    Priya, Shashank
    SCIENTIFIC REPORTS, 2017, 7
  • [4] Optimization of segmented thermoelectric generator using Taguchi and ANOVA techniques
    Ravi Anant Kishore
    Mohan Sanghadasa
    Shashank Priya
    Scientific Reports, 7
  • [5] Optimization of the Cutting Fluids and Parameters Using Taguchi and ANOVA in Milling
    Kuram, E.
    Simsek, B. T.
    Ozcelik, B.
    Demirbas, E.
    Askin, S.
    WORLD CONGRESS ON ENGINEERING, WCE 2010, VOL II, 2010, : 1292 - 1296
  • [6] Taguchi DoE and ANOVA: A systematic perspective for performance optimization of cross-coupled channel length modulation OTA
    Kumar, Tangudu Bharat
    Panda, Apurbaranjan
    Sharma, Gaurav Kumar
    Johar, Arun Kishor
    Kar, Sougata Kumar
    Boolchandani, Dharmendar
    AEU-INTERNATIONAL JOURNAL OF ELECTRONICS AND COMMUNICATIONS, 2020, 116
  • [7] A Study on Optimization of Process Parameters in EDM Using Taguchi's Doe Technique
    Ramalingam, V.
    Sivasubramanian, R.
    Kumar, M. Senthil
    JOURNAL FOR MANUFACTURING SCIENCE AND PRODUCTION, 2007, 8 (2-4) : 181 - 186
  • [8] Optimization of Cutting Parameters in Drilling Of AISI 304 Stainless Steel Using Taguchi and ANOVA
    Balaji, M.
    Murthy, B. S. N.
    Rao, N. Mohan
    1ST GLOBAL COLLOQUIUM ON RECENT ADVANCEMENTS AND EFFECTUAL RESEARCHES IN ENGINEERING, SCIENCE AND TECHNOLOGY - RAEREST 2016, 2016, 25 : 1106 - 1113
  • [9] CNC turning process parameters optimization on Aluminium 6082 alloy by using Taguchi and ANOVA
    Palaniappan, S. P.
    Muthukumar, K.
    Sabariraj, R. V.
    Kumar, S. Dinesh
    Sathish, T.
    MATERIALS TODAY-PROCEEDINGS, 2020, 21 : 1013 - 1021
  • [10] Optimization of Cutting Process Parameters on AL6061 Using ANOVA and TAGUCHI Method
    Niranjan, D. B.
    Shivashankar, G. S.
    Rao, Sreenivas K., V
    Praveen, R.
    MATERIALS TODAY-PROCEEDINGS, 2017, 4 (10) : 10845 - 10849