The influence of selective laser melting (SLM) parameters on physical, and mechanical properties of AlSi10Mg cylindrical specimen

被引：0
|
作者：
Mohan, R. Raj [1 ]
Krishnan, Navaneetha S. [1 ]
Sakthivel, B. [1 ]
Ramya, J. [2 ]
Sindhumathi, R. [1 ]
机构：
[1] SASTRA Univ, Bajaj Engn Skills Training BEST Ctr, Thanjavur 613401, Tamil Nadu, India
[2] SASTRA Univ, Sch Comp, Thanjavur 613401, Tamil Nadu, India
来源：
PHYSICA SCRIPTA | 2025年 / 100卷 / 02期
关键词：
WEAR BEHAVIOR; OPTIMIZATION; SURFACE; ALLOY; MICROSTRUCTURE; DENSIFICATION; POROSITY; QUALITY;
D O I：
10.1088/1402-4896/ada46c
中图分类号：
O4 [物理学];
学科分类号：
0702 ;
摘要：
AlSi10Mg cylindrical specimens were fabricated using the Laser-based Powder Bed Fusion (L-PBF) process, focusing on optimizing scanning speed, hatch spacing, and layer height through the box-behnken design (BBD). The study aimed to minimize surface roughness and maximize relative density. The analysis involved ANOVA, regression analysis, and composite desirability, revealing that hatch spacing and layer height significantly influence relative density and surface roughness. Under optimized conditions (scanning speed: 500 mm s-1, hatch spacing: 100 microns, layer height: 30 microns), the L-PBF specimen achieved a 96.70% relative density, 2.07 microns surface roughness (Ra), and an average microhardness of 124.9 HV0.5 (longitudinal) and 120.5 HV0.5 (transverse).
引用
收藏
页数：13
相关论文
共 50 条
  • [41] Rapid Solidification: Selective Laser Melting of AlSi10Mg
    Ming Tang
    P. Chris Pistorius
    Sneha Narra
    Jack L. Beuth
    JOM, 2016, 68 : 960 - 966
  • [42] Benchmarking of Dimensional Accuracy and Surface Roughness for AlSi10Mg Part by Selective Laser Melting (SLM)
    Kamarudin, K.
    Wahab, M. S.
    Raus, A. A.
    Ahmed, Aqeel
    Shamsudin, S.
    7TH INTERNATIONAL CONFERENCE ON MECHANICAL AND MANUFACTURING ENGINEERING (ICME'16), 2017, 1831
  • [43] A review on the simulation of selective laser melting AlSi10Mg
    Wang, Xingyao
    Lu, Qinghua
    Zhang, Peilei
    Yan, Hua
    Shi, Haichuan
    Sun, Tianzhu
    Zhou, Kai
    Chen, Kaiyuan
    OPTICS AND LASER TECHNOLOGY, 2024, 174
  • [44] Determination of Heat Transfer Coefficient by Inverse Analyzing for Selective Laser Melting (SLM) of AlSi10Mg
    Wu, Chongjun
    Xu, Weichun
    Wan, Shanshan
    Luo, Chao
    Lin, Zhijian
    Jiang, Xiaohui
    CRYSTALS, 2022, 12 (09)
  • [45] Dimensional Accuracy and Surface Roughness Analysis for AlSi10Mg Produced by Selective Laser Melting (SLM)
    Kamarudin, K.
    Wahab, M. S.
    Shayfull, Z.
    Ahmed, Aqeel
    Raus, A. A.
    2ND INTERNATIONAL CONFERENCE ON GREEN DESIGN AND MANUFACTURE 2016 (ICONGDM 2016), 2016, 78
  • [46] Effect of Heat Treatment on the Anisotropic Mechanical Properties of AlSi10Mg Fabricated by Selective Laser Melting
    Xu, Shijun
    Lu, Qinghua
    Ou, Yangling
    Zhang, Peilei
    Yan, Hua
    Sun, Tianzhu
    Ma, Songyun
    Luo, Zhirong
    Tian, Yingtao
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2024, 33 (19) : 10401 - 10414
  • [47] CNT-reinforced AlSi10Mg composite by selective laser melting: microstructural and mechanical properties
    Liu, Xihe
    Zhao, Congcong
    Zhou, Xin
    Eibl, Florian
    Shen, Zhijian
    Liu, Wei
    Meiners, Wilhelm
    MATERIALS SCIENCE AND TECHNOLOGY, 2019, 35 (09) : 1038 - 1045
  • [48] Effects of graphene on the mechanical properties of AlSi10Mg melted by SLM
    Qiu, Jiaqing
    Chen, Changjun
    Zhang, Min
    MATERIALS SCIENCE AND TECHNOLOGY, 2022, 38 (12) : 804 - 814
  • [49] Effect of process parameters on residual stress in selective laser melting of AlSi10Mg
    Jiang, Xiaohui
    Ye, Tong
    Zhu, Yihong
    MATERIALS SCIENCE AND TECHNOLOGY, 2020, 36 (03) : 342 - 352
  • [50] Anisotropic Mechanical Behavior of AlSi10Mg Parts Produced by Selective Laser Melting
    Ming Tang
    Petrus Christiaan Pistorius
    JOM, 2017, 69 : 516 - 522
12345