Promising processes of rolling and drawing of small-diameter bearing tubes

被引：0

作者：

Kharitonov, V.V. ^{[1
]}

Ermakov, V.M. ^{[1
]}

Ivko, D.M. ^{[1
]}

Zyryanov, A.E. ^{[1
]}

Zyryanova, V.S. ^{[1
]}

机构：

[1] Ural'skij Gosudarstvennyj, Tekhnicheskij Univ, Ekaterinburg, Russia

来源：

Stal' | 1994年 / 04期

关键词：

Bearing mountings - Cold rolling - Deformation - Drawing (forming) - Hardening - Heat treatment - Hot rolling - Microstructure - Steel - Temperature control;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

It is shown that it is possible to raise the rate and to extend the range of the production of small bearing tubes. This results from an advanced flow-sheet which involves screw- and lengthwise rolling of a billet less than 60 mm in diameter followed by single-pass or multipass plug and/or without mandrel drawing. These processes were used to manufacture a commercial lot of bearing tubes of a steel ShKh15 23×45 mm, 31×4.5 mm in size, etc.

引用

页码：56 / 58

共 50 条

[21] ULTRASONIC INSPECTION TECHNIQUE FOR FILLET WELDS IN SMALL-DIAMETER TUBES
KRAKOVYAK, MF
RAKHMANOV, VV
GREBENNIK, IL
WELDING PRODUCTION, 1971, 18 (09): : 61 - +
[22] Design evaluation of multiroll mills for small-diameter wire rolling
Kuroda, K
Kuboki, T
Imamura, Y
Hayashi, C
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 2001, 215 (01) : 77 - 86
[23] Penetration resistance and the bearing capacity of small-diameter steel piles
Vestberg, H. G.
Mann, G.
Holtz, R. D.
Proceedings of the 16th International Conference on Soil Mechanics and Geotechnical Engineering, Vols 1-5: GEOTECHNOLOGY IN HARMONY WITH THE GLOBAL ENVIRONMENT, 2005, : 2057 - 2060
[24] Penetration resistance and the bearing capacity of small-diameter steel piles
Swedish Geotechnical Institute, Linköping, Sweden
不详
不详
1600, 2057-2060 (2005):
[25] Simulation and experimental study on ECT of circumferential cracks in small-diameter tubes
Yin, Zun
Li, Jiaojiao
Meng, Yongle
Qin, Jianzhu
Tang, Dianwu
Hou, Zhaotang
Li, Zhaoyang
AIP ADVANCES, 2023, 13 (02)
[26] FORMING CHARACTERISTICS OF SMALL-DIAMETER AND HEAVY-WALL ERW TUBES
MINAMIYA, S
WATANABE, S
SUGIE, Y
TOYOOKA, T
IDE, T
HOSHI, K
TRANSACTIONS OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 25 (12) : B353 - B353
[27] COIL DRAWING OF SMALL DIAMETER TUBES OF CARBON STEELS.
Lobanov, A.I.
Vaschilo, T.P.
Moiseev, V.V.
1600, (14):
[28] The parameters of slug flow in small-diameter tubes under bubbling conditions
Omar K.
Pokhvalov Y.E.
Therm Eng, 2007, 1 (61-64): : 61 - 64
[29] Pressure drop with highly subcooled flow boiling in small-diameter tubes
Tong, W
Bergles, AE
Jensen, MK
EXPERIMENTAL THERMAL AND FLUID SCIENCE, 1997, 15 (03) : 202 - 212
[30] FORMING CHARACTERISTICS OF SMALL-DIAMETER AND HEAVY-WALL ERW TUBES
SUGIE, Y
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 (05): : S367 - S367

← 1 2 3 4 5 →