Development of heavy gauge 60 kgf/mm2 class tensile strength steel plate with low yield ratio for architecture use

被引：0

作者：

Shikanai, Nobuo ^{[1
]}

Sakui, Sin ^{[1
]}

Tagawa, Hisatoshi ^{[1
]}

Watanabe, Itaru ^{[1
]}

Narita, Hiroshi ^{[1
]}

Naganawa, Yutaka ^{[1
]}

机构：

[1] NKK Corp

来源：

NKK Technical Review | 1988年 / 54期

关键词：

Buildings--Tall - Plates--Steel - Steel Heat Treatment--Thermomechanical Treatment - Steel Testing--Tensile Tests;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

The 50 kgf/mm2 class tensile strength steel plates with low Yield Ratio (YR) have been widely applied to steel-frame buildings. On the other hand, conventional 60 kgf/mm2 class tensile strength steel plates have rarely been applied to steel-frame buildings because of higher YR compared with 50 kgf/mm2 class steel plates. However, application of high strength steel plates brings about many advantages such as saving welding cost, introducing new techniques into structural design and so on. In the present paper, the influence of heat treatment conditions and Thermo-Mechanical Control Process on yield and tensile strengths and YR was investigated in order to develop the heavy gauge 60 kgf/mm2 class steel plate with low YR.

引用

页码：1 / 7

共 50 条

[31] PROPERTIES OF SUBMERGED-ARC WELDED JOINT IN ULTRA-HEAVY THICK 100 KGF/MM2 STEEL PLATE
MINAGAWA, S
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 : 1523 - 1523
[32] HIGH-TENSILE STRENGTH STEEL PLATES PRODUCED BY CONTINUOUS ONLINE CONTROL PROCESS .7. DEVELOPMENT OF THICK STEEL PLATES WITH TENSILE-STRENGTH OF 50 KGF/MM2 FOR ARCTIC SERVICE
TSUZUKI, T
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 : 1385 - 1385
[33] THE DEVELOPMENT OF HEAVY THICK STEEL PLATES FOR ARCTIC OFFSHORE STRUCTURE BY ACCELERATED COOLING .2. CHARACTERISTICS OF HEAVY THICK STEEL PLATES WITH 50 KGF/MM2 TENSILE-STRENGTH FOR ARCTIC OFFSHORE STRUCTURE BY ACCELERATED COOLING
YAMAUCHI, M
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 : 1383 - 1383
[34] PROPERTIES OF CLASS 80KGF/MM2 GRADE HIGH STRENGTH HEAVY SECTION STEEL PLATES FOR JACK-UP RIG RACKS.
Iwasaki, Nobuhiro
Tagawa, Hisatoshi
Watanabe, Itaru
Yamada, Makoto
Nagamine, Takashi
Endo, Genkichi
Nippon Kokan technical report overseas, 1980, (30): : 1 - 12
[35] LOW-ALLOY STEEL WITH A STRENGTH OF 57KGF/MM2 FOR LARGE-DIAMETER GAS PIPELINES
MATROSOV, YI
LITVINENKO, DA
MOROZOV, YD
GLEBOVA, VS
MOROSHNICHENKO, SI
STEEL IN THE USSR, 1974, 4 (07): : 585 - 587
[36] 50-55 kgf/mm2 CLASS COLD ROLLED HIGH STRENGTH STEEL SHEETS FOR DEEP DRAWING.
Kokubo, Ichiro
Nomura, Shingo
Kameno, Katsumi
R and D: Research and Development Kobe Steel Engineering Reports, 1983, 33 (04): : 66 - 69
[37] YP690 N/mm2 Class Heavy Gauge Steel Plates with Extreme Low Temperature Toughness for Offshore Structures
JFE Technical Report, 2021, (26): : 180 - 182
[38] DEVELOPMENT OF TENSILE STRENGTH 50 kgf/mm2 GRADE STEEL PLATES FOR ARCTIC OFFSHORE STRUCTURES WITH HIGH TOUGHNESS IN LARGE HEAT INPUT WELDS (INVESTIGATION OF LARGE HEAT INPUT WELDABILITY OF STEEL PLATES WITH 50 kgf/mm2 GRADE FOR ARCTIC OFFSHORE STRUCTURES III).
Furusawa, Jun
Arimochi, Kazushige
Watanabe, Seiichi
Kurayasu, Hirofumi
Bessyo, Kiyoshi
Nakano, Naokazu
Suzuki, Shu-ichi
Transactions of the Iron and Steel Institute of Japan, 1986, 27 (01)
[39] DEVELOPMENT OF 80 kg/mm2 TENSILE STRENGTH STEEL FOR PREVENTING THE STRESS RELIEF CRACKING.
Arimochi, Kazushige
Ohnori, Yasuya
Kawaguchi, Yoshiaki
Sumitomo Metals, 1979, 31 (04): : 13 - 23
[40] FATIGUE-STRENGTH OF 80 KGF/MM2 GRADE HIGH-YIELD STRENGTH STEEL WITH NOTCH IN SEA-WATER BY CATHODIC PROTECTION
SUMITA, M
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 1985, 71 : 1420 - 1420

← 1 2 3 4 5 →