A study of the effect of tool cutting edge radius on ductile cutting of silicon wafers

被引：0
|
作者：
Liu, K. [2 ]
Li, X.P. [1 ]
Rahman, M. [1 ]
Neo, K.S. [1 ]
Liu, X.D. [2 ]
机构：
[1] Department of Mechanical Engineering, National University of Singapore, 10 Kent Ridge Crescent, Singapore 119260, Singapore
[2] Machining Technology Group, Singapore Institute of Manufacturing Technology, 71 Nanyang Drive, Singapore 638075, Singapore
来源：
International Journal of Advanced Manufacturing Technology | 2007年 / 32卷 / 7-8期
关键词：
Ductile mode cutting of silicon wafers can be achieved under certain cutting conditions and tool geometry. An experimental investigation of the critical undeformed chip thickness in relation to the tool cutting edge radius for the brittle-ductile transition of chip formation in cutting of silicon wafers is presented in this paper. Experimental tests for cutting of silicon wafers using diamond tools of different cutting edge radii for a range of undeformed chip thickness are conducted on an ultra-precision lathe. Both ductile and brittle mode of chip formation processes are observed in the cutting tests. The results indicate that ductile cutting of silicon can be achieved at certain values of the undeformed chip thickness; which depends on the tool cutting edge radius. It is found that in cutting of silicon wafers with a certain tool cutting edge radius there is a critical value of undeformed chip thickness beyond which the chip formation changes from ductile mode to brittle mode. The ductile-brittle transition of chip formation varies with the tool cutting edge radius. Within the range of cutting conditions in the present study; it has also been found that the larger the cutting edge radius; the larger the critical undeformed chip thickness for the ductile-brittle transition in the chip formation. © Springer-Verlag London Limited 2007;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Journal article (JA)
引用
收藏
页码：631 / 637
相关论文
共 50 条
  • [31] Tool edge radius effect on cutting temperature in micro-end-milling process
    Yang, Kai
    Liang, Ying-chun
    Zheng, Kang-ning
    Bai, Qing-shun
    Chen, Wan-qun
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2011, 52 (9-12): : 905 - 912
  • [32] Effect of crystalline orientation of a diamond tool on the machined surface in ductile mode cutting of silicon
    Li, X. P.
    Cai, M. B.
    Neo, W. C. L.
    Seah, K. H. W.
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2008, 222 (12) : 1597 - 1603
  • [33] A study on the tool edge geometry effect on nano-cutting
    Feifei Xu
    Jinshi Wang
    Fengzhou Fang
    Xiaodong Zhang
    The International Journal of Advanced Manufacturing Technology, 2017, 91 : 2787 - 2797
  • [34] A study on the tool edge geometry effect on nano-cutting
    Xu, Feifei
    Wang, Jinshi
    Fang, Fengzhou
    Zhang, Xiaodong
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 91 (5-8): : 2787 - 2797
  • [35] Molecular Dynamics Simulation of the Influence of Cutting Edge Radius on the Size Effect in Micro Cutting
    Gan, Qian
    Liang, He Ning Li
    Meng, Zhao
    PROCEEDINGS OF THE 8TH INTERNATIONAL CONFERENCE ON MULTI-MATERIAL MICRO MANUFACTURE (4M 2011), 2011, : 87 - 91
  • [36] Influence of cutting edge geometry and cutting edge radius on the stability of micromilling processes
    Biermann D.
    Baschin A.
    Prod. Eng., 2009, 4-5 (375-380): : 375 - 380
  • [37] Influence of cutting edge radius on cutting forces in machining titanium
    Wyen, C. -F.
    Wegener, K.
    CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2010, 59 (01) : 93 - 96
  • [38] A state-of-the-art review of ductile cutting of silicon wafers for semiconductor and microelectronics industries
    Arif, Muhammad
    Rahman, Mustafizur
    San, Wong Yoke
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2012, 63 (5-8): : 481 - 504
  • [39] A state-of-the-art review of ductile cutting of silicon wafers for semiconductor and microelectronics industries
    Muhammad Arif
    Mustafizur Rahman
    Wong Yoke San
    The International Journal of Advanced Manufacturing Technology, 2012, 63 : 481 - 504
  • [40] Influence of Cutting Edge Radius on Tool Life in Milling Inconel 718
    Celaya, A.
    Pereira, O.
    Gonzalez, H.
    Gomez-Escudero, G.
    Fernandez-Lucio, P.
    Fernandez-Valdivielso, A.
    Lopez de lacalle, L. N.
    PROCEEDINGS OF THE 22ND INTERNATIONAL ESAFORM CONFERENCE ON MATERIAL FORMING (ESAFORM 2019), 2019, 2113
12345