Rolling of Al-Cu bimetallic bars in modified elongating grooves

被引：0

作者：

Mróz, Sebastian ^{[1
]}

Szota, Piotr ^{[1
]}

Wąsek, Seweryn ^{[1
]}

Stefanik, Andrzej ^{[1
]}

机构：

[1] Częstochowa University of Technology, Institute of Metal Forming and Safety Enginering, Al. Armii Krajowej 19, Czestochowa,42-200, Poland

来源：

Solid State Phenomena | 2015年 / 220-221卷

关键词：

Explosive welding - Cladding (coating) - Copper alloys - Explosives - Aluminum alloys;

D O I：

10.4028/www.scientific.net/SSP.220-221.875

中图分类号：

学科分类号：

摘要：

In order to enhance the uniformity of cladding copper layer distribution over the bimetallic bar perimeter and length, the shape of the classical horizontal and vertical oval passes were modified. The rolling was carried out in the designed modified elongating grooves. The round Al-Cu bimetallic bars with an outer diameter of 22 mm and a copper layer share of 15 and 30%, after explosive cladding, were rolled on a D150 two-high shape mill. As a result of rolling in 4 passes, bars of a diameter of about 16.0 mm were obtained. By applying the modified grooves to the rolling of Al-Cu bimetallic bars, the stability of the rolling process was improved, whereby, finished bars with a uniform and tight cladding layer distribution over the core and small diameter dimensional deviations was obtained. © (2015) Trans Tech Publications, Switzerland.

引用

页码：875 / 880

共 50 条

[21] GROOVE ROLLING PROCESS OF Mg/AI BIMETALLIC BARS
Mroz, S.
Stefanik, A.
Szota, P.
ARCHIVES OF METALLURGY AND MATERIALS, 2019, 64 (03) : 1067 - 1072
[22] Influence of precipitates on the microstructure and texture during the rolling of Al-Cu and Al-Mn single crystals with rolling texture orientations
Engler, O
Kong, XW
Lücke, K
PHILOSOPHICAL MAGAZINE A-PHYSICS OF CONDENSED MATTER STRUCTURE DEFECTS AND MECHANICAL PROPERTIES, 2001, 81 (03): : 543 - 570
[23] Simultaneously increasing the strength and ductility of the modified casting Al-Cu alloy
Zhao W.
Wang H.
Wang J.
Li Y.
Jiang Q.
J Mater Res, 2008, 4 (1076-1081): : 1076 - 1081
[24] Wear behavior of Al-Cu and Al-Cu/SiC components produced by powder metallurgy
Hassan, Adel Mahamood
Mayyas, Ahmad Turki
Alrashdan, Abdalla
Hayajneh, Mohammed T.
JOURNAL OF MATERIALS SCIENCE, 2008, 43 (15) : 5368 - 5375
[25] Simultaneously increasing the strength and ductility of the modified casting Al-Cu alloy
Zhao, Wengui
Wang, Huiyuan
Wang, Jinguo
Li, Yong
Jiang, Qichuan
JOURNAL OF MATERIALS RESEARCH, 2008, 23 (04) : 1076 - 1081
[26] The effects of temperature on wear behaviours of Al-Cu alloy and Al-Cu/SiC composite
Muratoglu, M
Aksoy, M
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2000, 282 (1-2): : 91 - 99
[27] THEORETICAL AND EXPERIMENTAL ANALYSIS OF THE Cu-Al BIMETALLIC BAR ROLLING PROCESS
Mroz, S.
Szota, P.
Dyja, H.
Kawalek, A.
METALURGIJA, 2011, 50 (02): : 85 - 88
[28] Deformation structures and strengthening mechanisms in an Al-Cu alloy subjected to extensive cold rolling
Zuiko, I.
Kaibyshev, R.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2017, 702 : 53 - 64
[29] Elaboration of Technological Process Criteria for Multicycle Rolling of Sliced Materials of System AL-CU
Galkin, V., I
Paltievich, A. R.
Galkin, E., V
OIL AND GAS ENGINEERING (OGE-2020), 2020, 2285
[30] THE THEORETICAL AND EXPERIMENTAL ANALYSIS OF THE POSSIBILITY OF EMPLOYING THE GROOVE ROLLING PROCESS FOR THE MANUFACTURE OF Mg/Al BIMETALLIC BARS
Mroz, S.
Szota, P.
Stefanik, A.
METALURGIJA, 2016, 55 (04): : 628 - 630

← 1 2 3 4 5 →