Heat transfer during pressing of 3d moulded veneer plywood composite materials

被引：5

作者：

Igaz R. ^{[1
]}

Krišták L. ^{[1
]}

Ružiak I. ^{[1
]}

Réh R. ^{[2
]}

Danihelová Z. ^{[3
]}

机构：

[1] Department of Physics, Electrotechnics and Applied Mechanics, Technical University in Zvolen, T. G. Masaryka 24, Zvolen

[2] Department of Mechanical Technology of Wood, Faculty of Wood Sciences and Technology, Technical University in Zvolen, T. G. Masaryka 24, Zvolen

[3] Institute of Foreign Languages, Faculty of Wood Sciences and Technology, Technical University in Zvolen, T. G. Masaryka 24, Zvolen

来源：

Key Engineering Materials | 2016年 / 688卷

关键词：

Beech Plywood; Heat Transfer; Mechanical Properties; Pressing Parameters; Pressing Temperature; Pressing Time;

D O I：

10.4028/www.scientific.net/KEM.688.131

中图分类号：

学科分类号：

摘要：

The paper deals with the research into the heat transfer during high temperature pressing of 3D moulded veneer plywood consisting of seven plies. Plywood was being pressed at two temperatures (110 °C and 120 °C), whereby the impact of the pressing temperature on the speed of heat transfer across the surface and through the mass of the pressed material was evaluated. Following the experiment the optimum pressing time was determined. Attention was paid also to the evaluation of impact of temperature on selected mechanical and physical properties of plywood. Following properties were evaluated: bending strength, modulus of elasticity in bending, compression degree and density. Results indicate that higher pressing temperature decreases the pressing time by 23,7 s representing a 7.3% time saving. In addition, higher pressing temperature increases slightly the bending strength (by 7.5%) as well as modulus of elasticity in bending (by 11.8%). © 2016 Trans Tech Publications, Switzerland.

引用

页码：131 / 137

页数：6

共 50 条

[31] Optimization of the Heat Transfer Simulation Time During 3D Printing of PLA Material
Benie, Kandy
Cherouat, Abel
Barriere, Thierry
Placet, Vincent
NUMERICAL METHODS IN INDUSTRIAL FORMING PROCESSES, NUMIFORM 2023, 2024, : 67 - 79
[32] 3D numerical simulation of heat transfer during dry drilling of Inconel 718
Chenegrin, Kevin
Roux, Jean-Christophe
Helfenstein-Didier, Clementine
Pouvreau, Cedric
Girinon, Mathieu
Karaouni, Habib
Bergheau, Jean-Michel
Feulvarch, Eric
JOURNAL OF MANUFACTURING PROCESSES, 2021, 64 : 1143 - 1152
[33] 3D moulded circuits stronger than boards
Shelley, Tom
Eureka, 1995, 15 (10) : 57 - 58
[34] Heat and moisture transfer in 3D Garment CAD
Du, Zuoyang
Xu, Qingzhen
2008 INTERNATIONAL SYMPOSIUM ON INTELLIGENT INFORMATION TECHNOLOGY APPLICATION, VOL III, PROCEEDINGS, 2008, : 455 - +
[35] Visualisation of heat transfer in 3D unsteady flows
Speetjens, M. F. M.
van Steenhoven, A. A.
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2010, 49 (07) : 1103 - 1114
[36] Heat transfer in 3D water and ice basins
Ceci, S.
De Biase, L.
Fossati, G.
ADVANCED COMPUTATIONAL METHODS IN HEAT TRANSFER IX, 2006, 53 : 143 - +
[37] 3D FEM Heat Transfer Simulation of Grinding
Weber D.
Kirsch B.
da Silva E.J.
Aurich J.C.
ZWF Zeitschrift fuer Wirtschaftlichen Fabrikbetrieb, 2022, 117 (7-8): : 484 - 488
[38] HEAT TRANSFER CHARACTERIZATION OF 3D PRINTABLE ARCHITECTED HEAT SINKS
Ali, Mohamed I. Hassan
Al-Ketan, Oraib
Alhammadi, Alya
Khalil, Mohamad
Khan, Kamran
Abu Al-Rub, Rashid K.
PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2019, VOL 8, 2019,
[39] Heat transfer performance in 3D internally finned heat pipe
Liao, Quan
Jen, Tien-Chen
Chen, Qinghua
Li, Longjian
Cui, Wenzhi
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2007, 50 (7-8) : 1231 - 1237
[40] Experimental and CFD simulation of the pool boiling heat transfer performance in a 3D MCFC composite structured
Kang, Yingjie
Lang, Zhongmin
Wu, Gangqiang
Wang, Yaxiong
Wang, Yunfei
Ouyang, Mingchao
Yu, Ying
APPLIED THERMAL ENGINEERING, 2024, 255

← 1 2 3 4 5 →