Heat transfer during pressing of 3d moulded veneer plywood composite materials

被引：5

作者：

Igaz R. ^{[1
]}

Krišták L. ^{[1
]}

Ružiak I. ^{[1
]}

Réh R. ^{[2
]}

Danihelová Z. ^{[3
]}

机构：

[1] Department of Physics, Electrotechnics and Applied Mechanics, Technical University in Zvolen, T. G. Masaryka 24, Zvolen

[2] Department of Mechanical Technology of Wood, Faculty of Wood Sciences and Technology, Technical University in Zvolen, T. G. Masaryka 24, Zvolen

[3] Institute of Foreign Languages, Faculty of Wood Sciences and Technology, Technical University in Zvolen, T. G. Masaryka 24, Zvolen

来源：

Key Engineering Materials | 2016年 / 688卷

关键词：

Beech Plywood; Heat Transfer; Mechanical Properties; Pressing Parameters; Pressing Temperature; Pressing Time;

D O I：

10.4028/www.scientific.net/KEM.688.131

中图分类号：

学科分类号：

摘要：

The paper deals with the research into the heat transfer during high temperature pressing of 3D moulded veneer plywood consisting of seven plies. Plywood was being pressed at two temperatures (110 °C and 120 °C), whereby the impact of the pressing temperature on the speed of heat transfer across the surface and through the mass of the pressed material was evaluated. Following the experiment the optimum pressing time was determined. Attention was paid also to the evaluation of impact of temperature on selected mechanical and physical properties of plywood. Following properties were evaluated: bending strength, modulus of elasticity in bending, compression degree and density. Results indicate that higher pressing temperature decreases the pressing time by 23,7 s representing a 7.3% time saving. In addition, higher pressing temperature increases slightly the bending strength (by 7.5%) as well as modulus of elasticity in bending (by 11.8%). © 2016 Trans Tech Publications, Switzerland.

引用

页码：131 / 137

页数：6

共 50 条

[11] Modeling 3D heat flow interaction with defects in composite materials for infrared thermography
Manohar, Arun
di Scalea, Francesco Lanza
NDT & E INTERNATIONAL, 2014, 66 : 1 - 7
[12] Composite materials with graphenic materials by extrusion for 3D printing
Martinez Borja, Ana Lilia
Perez Bueno, Jose de Jesus
Mendoza Lopez, Maria Luisa
MRS ADVANCES, 2018, 3 (64): : 3891 - 3898
[13] Composite materials with graphenic materials by extrusion for 3D printing
Ana Lilia Martínez Borja
José de Jesús Pérez Bueno
Maria Luisa Mendoza Lopez
MRS Advances, 2018, 3 (64) : 3891 - 3898
[14] Thermionic enhanced heat transfer in electronic devices based on 3D Dirac materials
Huang, Sunchao
Lewis, R. A.
Zhang, Chao
JOURNAL OF APPLIED PHYSICS, 2019, 126 (16)
[15] Using 3D simulation for the optimization of injection moulded thermoset materials for automotive applications
Kallien, LH
De Keyser, H
INJECTION MOULDING 2002, CONFERENCE PROCEEDINGS: ADVANCES IN PLASTIC INJECTION MOULDING TECHNOLOGY, 2002, : 13 - 25
[16] MODELING OF 3D ELECTROMAGNETIC AND HEAT-TRANSFER PHENOMENA FOR MATERIALS WITH POOR CONDUCTIVITY
MIMOUNE, SM
FOULADGER, J
DEVELEY, G
IEEE TRANSACTIONS ON MAGNETICS, 1995, 31 (06) : 3578 - 3580
[17] Numerical 3D Simulation of Heat Transfer during Friction Stir Welding
Albagachiev, A. Yu.
Usov, P. P.
JOURNAL OF MACHINERY MANUFACTURE AND RELIABILITY, 2022, 51 (SUPPL 1) : S94 - S99
[18] Numerical 3D Simulation of Heat Transfer during Friction Stir Welding
A. Yu. Albagachiev
P. P. Usov
Journal of Machinery Manufacture and Reliability, 2022, 51 : S94 - S99
[19] Simulation of the Process of Heat and Mass Transfer in Composite Materials During Fire
Kasymov, D. P.
Perminov, V. V.
Shevlyakova, A. A.
Yakimov, A. S.
JOURNAL OF ENGINEERING PHYSICS AND THERMOPHYSICS, 2023, 96 (03) : 604 - 611
[20] Deflection Characteristics and Heat Transfer of Plywood for Wood-based Flooring by Cross-band Veneer Composition
Pi, Duck-Won
Kang, Seog-Goo
Hasegawa, Masumi
JOURNAL OF THE FACULTY OF AGRICULTURE KYUSHU UNIVERSITY, 2013, 58 (01): : 109 - 114

← 1 2 3 4 5 →