Electron Backscatter Diffraction (EBSD) analysis of laser-cladded AISI 420 martensitic stainless steel

被引：0
|
作者：
Alam, Mohammad K. [1 ]
Mehdi, Mehdi [1 ]
Urbanic, Ruth Jill [1 ]
Edrisy, Afsaneh [1 ]
机构：
[1] Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Ave., Windsor,Ontario,N9B 3P4, Canada
来源：
Materials Characterization | 2020年 / 161卷
关键词：
Laser cladding is a laser-based additive manufacturing (AM) process that is currently being used to coat part of a substrate or to produce a three-dimensional object in layer by layer following a computer-controlled instruction. In this study; laser-cladded AISI 420 martensitic stainless steel was characterized using the Electron Backscatter Diffraction (EBSD) technique to analyze the substructure of martensite in the selected zones such as the bead zone (BZ); the dilution zone (DZ); and the interface with the heat affected zone (HAZ) of the bead. The EBSD prior austenite grain (PAG) maps and inverse pole figure (IPF) revealed planer and columnar grains at the interface and within the adjacent dilution zone; while equiaxed and a combination of both columnar and equiaxed grains were observed in the center of the bead and dilution zone. The Grain Orientation Spread (GOS) and grain average Image Quality (IQ) techniques were used to quantify the grain misorientation and residual strain/stress in those selected zones. The EBSD analysis with the GOS and IQ values confirmed deformation and strain in the crystal lattice structure of those respective zones. The GOS approach revealed that most of the grains at the BZ and HAZ were highly strained and 26–59% fraction of the grains was at a high angle of GOS (3°–5°) indicating the availability of highly deformed grains in both regions. The IQ value was compared and correlated with the experimental values of residual stresses (RS) measured by XRD methods to understand residual strain distribution in those zones. It was revealed that the IQ value is inversely proportional to the RS value found in an earlier study. This EBSD parameter is expected to be used as an alternative method of analyzing RS distribution in the laser-cladded coating. © 2020 Elsevier Inc;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
引用
收藏
相关论文
共 50 条
  • [41] Effect of Austenitizing Heat Treatment on the Microstructure and Hardness of Martensitic Stainless Steel AISI 420
    L. D. Barlow
    M. Du Toit
    Journal of Materials Engineering and Performance, 2012, 21 : 1327 - 1336
  • [42] Influence of the heat treatment on the corrosion resistance of the martensitic stainless steel type AISI 420
    Candelária, AF
    Pinedo, CE
    JOURNAL OF MATERIALS SCIENCE LETTERS, 2003, 22 (16) : 1151 - 1153
  • [43] WEAR BEHAVIOR OF NITROGEN-IMPLANTED AISI 420 MARTENSITIC STAINLESS-STEEL
    ONATE, JI
    DENNIS, JK
    HAMILTON, S
    SURFACE & COATINGS TECHNOLOGY, 1990, 42 (02): : 119 - 131
  • [44] Martensitic stainless steel AISI 420-mechanical properties, creep and fracture toughness
    Brnic, J.
    Turkalj, G.
    Canadija, M.
    Lanc, D.
    Krscanski, S.
    MECHANICS OF TIME-DEPENDENT MATERIALS, 2011, 15 (04) : 341 - 352
  • [45] Effect of Austenitizing Heat Treatment on the Microstructure and Hardness of Martensitic Stainless Steel AISI 420
    Barlow, L. D.
    Du Toit, M.
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2012, 21 (07) : 1327 - 1336
  • [46] Microstructure and Hardness of High Temperature Gas Nitrided AISI 420 Martensitic Stainless Steel
    Ibrahim, Nor Nurulhuda Md.
    Hussain, Patthi
    Awang, Mohktar
    ICPER 2014 - 4TH INTERNATIONAL CONFERENCE ON PRODUCTION, ENERGY AND RELIABILITY, 2014, 13
  • [47] Failure Prediction of AISI 420 Martensitic Stainless Steel Using the Theory of Critical Distances
    Siqueira, Marcelo de Oliveira
    de Carvalho, Eduardo Atem
    MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS, 2020, 23 (06):
  • [48] Microstructure of Plasma Nitrided AISI420 Martensitic Stainless Steel at 673 K
    Aizawa, Tatsuhiko
    Yoshino, Tomoaki
    Morikaw, Kazuo
    Yoshihar, Sho-Ichiro
    CRYSTALS, 2019, 9 (02):
  • [49] Effects of loading conditions on free surface roughening of AISI 420 martensitic stainless steel
    Solhjoo, Soheil
    Halbertsma, Pieter J.
    Veldhuis, Mark
    Toljaga, Ranko
    Pei, Yutao
    Vakis, Antonis, I
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2020, 275
  • [50] Formation of Nanospikes on AISI 420 Martensitic Stainless Steel under Gallium Ion Bombardment
    Cenev, Zoran
    Bartenwerfer, Malte
    Klauser, Waldemar
    Jokinen, Ville
    Fatikow, Sergej
    Zhou, Quan
    NANOMATERIALS, 2019, 9 (10)
12345