Experimental study on green electrical discharge machining in tap water of Ti-6Al-4V and parameters optimization

被引：0
|
作者：
机构：
[1] Tang, L.
[2] Du, Y.T.
来源：
Tang, L. (tang_lin168@yahoo.com) | 1600年 / Springer London卷 / 70期
关键词：
Ti-6Al-4V is widely used in the aerospace; automobile; and biomedical fields; but is a difficult-to-machine material. Electrical discharge machining (EDM) is regarded as one of the most effective approaches tomachining Ti-6Al-4V alloy; since it is a non-contact electro-thermal machining method; and it is independent from the mechanical properties of the processed material. This paper aims to combine grey relational analysis and Taguchi methods to solve the problem of EDM parameters optimization. From the viewpoint of health and environment; tap water as working fluid has good working environment; since it does not release harmful gas. The process parameters include discharge current; gap voltage; lifting height; negative polarity and pulse duty factor. The electrode wear ratio (EWR); material removal rate (MRR) and surface roughness (SR) as objective parameters are chosen to evaluate the whole machining effects. Experiments were carried out based on Taguchi L9 orthogonal array and grey relational analysis; and then verified the results through a confirmation experiment. Compared the machining parameters A1B1C 3D2 with A1B2C2D 2; MRR increased from 1.28 mm3/min to 2.38 mm3/min; EWR decreased from 0.14 to 0.10 mm3/min and SR decreased from Ra 2.37 μm to Ra 1.93 μm. The process parameters sequenced in order of relative importance are: the ratio of pulse width to pulse interval; discharge current; lifting height and gap voltage. The results showed that using tap water machining Ti-6Al-4V material can obtain high MRR; decrease the machining cost and have no harmful to the operators and the environment. © Springer-Verlag London 2013;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Journal article (JA)
引用
收藏
页码：1 / 4
相关论文
共 50 条
  • [31] Experimental Study of Machining Characteristics of Titanium Alloy (Ti-6Al-4V)
    Sharma, Arunil
    Sharma, Mukund Dutt
    Sehgal, Rakesh
    ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING, 2013, 38 (11) : 3201 - 3209
  • [32] A Study on Kerf and Material Removal Rate in Wire Electrical Discharge Machining of Ti-6Al-4V:Multi-Objectives Optimization
    Saedon, J. B.
    Nor, N. H. Mohamad
    Jaafar, Norkamal
    Husain, Hazran
    Yahaya, Mohd Azman
    2014 2ND INTERNATIONAL CONFERENCE ON TECHNOLOGY, INFORMATICS, MANAGEMENT, ENGINEERING, AND ENVIRONMENT (TIME-E 2014), 2014, : 111 - 116
  • [33] Research on the efficient and stable sinking electrical discharge machining ablation process of Ti-6Al-4V
    Kong, Linglei
    Liu, Zhidong
    Han, Yunxiao
    Qiu, Mingbo
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 97 (5-8): : 2151 - 2161
  • [34] Research on the efficient and stable sinking electrical discharge machining ablation process of Ti-6Al-4V
    Linglei Kong
    Zhidong Liu
    Yunxiao Han
    Mingbo Qiu
    The International Journal of Advanced Manufacturing Technology, 2018, 97 : 2151 - 2161
  • [35] Mechanical Surface Treatments of Ti-6Al-4V Miniplate Implant Manufactured by Electrical Discharge Machining
    Qosim, N.
    Supriadi, S.
    Puspitasari, P.
    Kreshanti, P.
    INTERNATIONAL JOURNAL OF ENGINEERING, 2018, 31 (07): : 1103 - 1108
  • [36] Monopulse electrical discharge machining ablation drilling technology for Ti-6Al-4V titanium alloy
    Cao, Zhongli
    Liu, Zhidong
    Wang, Xiangzhi
    Qiu, Mingbo
    Hui, Zhiguang
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2016, 86 (1-4): : 539 - 546
  • [37] Monopulse electrical discharge machining ablation drilling technology for Ti-6Al-4V titanium alloy
    Zhongli Cao
    Zhidong Liu
    Xiangzhi Wang
    Mingbo Qiu
    Zhiguang Hui
    The International Journal of Advanced Manufacturing Technology, 2016, 86 : 539 - 546
  • [38] Hydroxyapatite Deposition onto Ti-6Al-4V Surface in Powder Mixed Electrical Discharge Machining
    Ekmekci, Nihal
    Ekmekci, Bulent
    MATERIAL SCIENCE AND ENGINEERING TECHNOLOGY II, 2014, 856 : 205 - 209
  • [39] PERFORMANCE ANALYSIS OF WIRE ELECTRODES ON MACHINING Ti-6Al-4V ALLOY USING ELECTRICAL DISCHARGE MACHINING PROCESS
    Ramamurthy, A.
    Sivaramakrishnan, R.
    Muthuramalingam, T.
    Venugopal, S.
    MACHINING SCIENCE AND TECHNOLOGY, 2015, 19 (04) : 577 - 592
  • [40] Improving the surface quality of Ti-6Al-4V alloy produced by electrical discharge machining with abrasive flow machining
    Gov, Kursad
    Soydan, Osman
    Eyercioglu, Omer
    JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY, 2020, 35 (03): : 1159 - 1170
12345