Structural and mechanical properties of Cu-SiCp nanocomposites fabricated by accumulative roll bonding (ARB)

被引:1
|
作者
Ghaderi, Omid [1 ]
Zare, Mehran [1 ]
Sadabadi, Hamed [1 ]
Toroghinejad, Mohammad Reza [2 ]
Najafizadeh, Abbas [2 ]
Church, Benjamin C. [1 ]
Rohatgi, Pradeep K. [1 ]
机构
[1] Univ Wisconsin, Dept Mat Sci & Engn, Milwaukee, WI 53211 USA
[2] Isfahan Univ Technol, Dept Mat Engn, Esfahan, Iran
来源
FRONTIERS IN MATERIALS | 2024年 / 11卷
关键词
copper-silicon carbide composite; accumulative roll bonding (ARB); microstructure; mechanical properties; fractography; texture parameter; reitveld method; SEVERE PLASTIC-DEFORMATION; MATRIX COMPOSITES; SHEAR STRAIN; GRAIN-SIZE; MICROSTRUCTURE; EVOLUTION; ALUMINUM; STRENGTH; TEXTURE; ALLOYS;
D O I
10.3389/fmats.2024.1362746
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
In this study, the accumulative roll bonding (ARB) method, a severe plastic deformation (SPD) process, was used to fabricate copper-2 wt% silicon carbide composite strips. The ARB process was successfully conducted for up to nine cycles on pure copper strips with silicon carbide particles distributed between them, as well as on monolithic copper. Equiaxed tensile and Vickers hardness tests were conducted to evaluate the mechanical properties of the samples. SEM was utilized to study the fracture surfaces and to determine the fracture mechanism of ARB processed monolithic copper and composite samples after the tensile test. Texture parameters were calculated through X-ray analysis. The Rietveld method using MAUD software were employed to assess the crystallite size of the samples. Results indicated that average amount of porosity decreased and interface bonding between copper strip layers improved with increasing the number of ARB cycles. Moreover, an increased number of cycles led to homogeneous distribution of SiC particles within the copper matrix. The tensile strength of the fabricated composites improved with an increase in the number of cycles, ultimately reaching 483 MPa after nine cycles, compared to 388 MPa for the composite processed with a single cycle of ARB and 194 MPa for annealed copper strips. Initially, the elongation of the composite samples decreased dramatically to about 6% after applying five cycle of ARB process from the 46% observed for annealed pure copper strip. However, it improved as the process continued, reaching 8.9% after the ninth cycle. Investigation of fracture surfaces after the tensile test using SEM revealed that the dominant failure mode was shear ductile fracture. Analysis of sample textures demonstrated that the dominant texture was (100). Crystallite sizes for pure copper and nine cycles-rolled composites, as determined by Reitveld method, reached 111 nm and 89 nm, respectively.
引用
收藏
页数:16
相关论文
共 50 条
  • [41] Evolution of Microstructure, Mechanical Properties, and Thermal Conductivity of an Al-Li-Cu-Mg-Zr Alloy Processed by Accumulative Roll Bonding (ARB)
    Aboubakr Medjahed
    Bingcheng Li
    Legan Hou
    Ruizhi Wu
    Abdeldjalil Zegaoui
    Mehdi Derradji
    Hocine Benyamina
    JOM, 2019, 71 : 4096 - 4104
  • [42] Passivation Behavior of Ultrafine-Grained Pure Copper Fabricated by Accumulative Roll Bonding (ARB) Process
    Arash Fattah-alhosseini
    Omid Imantalab
    Metallurgical and Materials Transactions A, 2016, 47 : 572 - 580
  • [43] Aluminium Alloys Nanostructures Produced by Accumulative Roll Bonding (ARB)
    Almaetah, Yazan M.
    Abushgair, Khaleel N.
    Hamdan, Mohammad A.
    JORDAN JOURNAL OF MECHANICAL AND INDUSTRIAL ENGINEERING, 2021, 15 (04): : 329 - 335
  • [44] Passivation Behavior of Ultrafine-Grained Pure Copper Fabricated by Accumulative Roll Bonding (ARB) Process
    Fattah-Alhosseini, Arash
    Imantalab, Omid
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2016, 47A (01): : 572 - 580
  • [45] Effects of Thermal Conditions on Microstructure and Mechanical Properties of Cu-SiCp Surface Nanocomposites by Friction Stir Processing Route
    Cartigueyen, S.
    Mahadevan, K.
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2019, 72 (02) : 289 - 305
  • [46] Electrical conductivity of multilayered Cu/Nb composites fabricated by accumulative roll bonding
    Justice, J.
    Bauyrzhan, A.
    Wang, Y.
    Khafizov, M.
    Cheng, J. Y.
    Mara, N. A.
    Mishra, S.
    Ronning, F.
    Anderoglu, O.
    JOURNAL OF APPLIED PHYSICS, 2025, 137 (04)
  • [47] Cu/Zr nanoscaled multi-stacks fabricated by accumulative roll bonding
    Sun, Y. F.
    Tsuji, N.
    Fujii, H.
    Li, F. S.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2010, 504 : S443 - S447
  • [48] Creep properties of bimetal Al/SiC/Cu composites fabricated via accumulative roll bonding process
    Ali, Basem
    Dheyaa, J. Jasim
    Pooja, Bansal
    Maytham, T. Qasim
    Brisset, B. J.
    JOURNAL OF CENTRAL SOUTH UNIVERSITY, 2024, 31 (10) : 3807 - 3818
  • [49] Microstructure evolution and mechanical properties of Al/Al-12%Si multilayer processed by accumulative roll bonding (ARB)
    El Mahallawy, Nahed
    Fathy, Adel
    Abdelaziem, Walaa
    Hassan, Mohammed
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2015, 647 : 127 - 135
  • [50] An investigation in to the mechanical properties of CP Ti/TiO2 nanocomposite manufactured by the accumulative roll bonding (ARB) process
    Moradgholi, J.
    Monshi, A.
    Farmanesh, K.
    CERAMICS INTERNATIONAL, 2017, 43 (01) : 201 - 207