Structural and mechanical properties of Cu-SiCp nanocomposites fabricated by accumulative roll bonding (ARB)

被引:1
|
作者
Ghaderi, Omid [1 ]
Zare, Mehran [1 ]
Sadabadi, Hamed [1 ]
Toroghinejad, Mohammad Reza [2 ]
Najafizadeh, Abbas [2 ]
Church, Benjamin C. [1 ]
Rohatgi, Pradeep K. [1 ]
机构
[1] Univ Wisconsin, Dept Mat Sci & Engn, Milwaukee, WI 53211 USA
[2] Isfahan Univ Technol, Dept Mat Engn, Esfahan, Iran
来源
FRONTIERS IN MATERIALS | 2024年 / 11卷
关键词
copper-silicon carbide composite; accumulative roll bonding (ARB); microstructure; mechanical properties; fractography; texture parameter; reitveld method; SEVERE PLASTIC-DEFORMATION; MATRIX COMPOSITES; SHEAR STRAIN; GRAIN-SIZE; MICROSTRUCTURE; EVOLUTION; ALUMINUM; STRENGTH; TEXTURE; ALLOYS;
D O I
10.3389/fmats.2024.1362746
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
In this study, the accumulative roll bonding (ARB) method, a severe plastic deformation (SPD) process, was used to fabricate copper-2 wt% silicon carbide composite strips. The ARB process was successfully conducted for up to nine cycles on pure copper strips with silicon carbide particles distributed between them, as well as on monolithic copper. Equiaxed tensile and Vickers hardness tests were conducted to evaluate the mechanical properties of the samples. SEM was utilized to study the fracture surfaces and to determine the fracture mechanism of ARB processed monolithic copper and composite samples after the tensile test. Texture parameters were calculated through X-ray analysis. The Rietveld method using MAUD software were employed to assess the crystallite size of the samples. Results indicated that average amount of porosity decreased and interface bonding between copper strip layers improved with increasing the number of ARB cycles. Moreover, an increased number of cycles led to homogeneous distribution of SiC particles within the copper matrix. The tensile strength of the fabricated composites improved with an increase in the number of cycles, ultimately reaching 483 MPa after nine cycles, compared to 388 MPa for the composite processed with a single cycle of ARB and 194 MPa for annealed copper strips. Initially, the elongation of the composite samples decreased dramatically to about 6% after applying five cycle of ARB process from the 46% observed for annealed pure copper strip. However, it improved as the process continued, reaching 8.9% after the ninth cycle. Investigation of fracture surfaces after the tensile test using SEM revealed that the dominant failure mode was shear ductile fracture. Analysis of sample textures demonstrated that the dominant texture was (100). Crystallite sizes for pure copper and nine cycles-rolled composites, as determined by Reitveld method, reached 111 nm and 89 nm, respectively.
引用
收藏
页数:16
相关论文
共 50 条
  • [31] Electrochemical and Passive Behaviors of Pure Copper Fabricated by Accumulative Roll-Bonding (ARB) Process
    O. Imantalab
    A. Fattah-alhosseini
    Journal of Materials Engineering and Performance, 2015, 24 : 2579 - 2585
  • [32] Electrochemical and Passive Behaviors of Pure Copper Fabricated by Accumulative Roll-Bonding (ARB) Process
    Imantalab, O.
    Fattah-alhosseini, A.
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2015, 24 (07) : 2579 - 2585
  • [33] Evaluation of mechanical properties and structure of multilayered Al/Ni composites produced by accumulative roll bonding (ARB) process
    Mozaffari, A.
    Manesh, H. Danesh
    Janghorban, K.
    JOURNAL OF ALLOYS AND COMPOUNDS, 2010, 489 (01) : 103 - 109
  • [34] Investigation on microstructure and mechanical properties of Al-Zn composite during accumulative roll bonding (ARB) process
    Dehsorkhi, Reza Nasiri
    Qods, Fathallah
    Tajally, Mohammad
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 530 : 63 - 72
  • [35] Microstructure and mechanical behaviors of Al/Cu laminated composites fabricated by accumulative roll bonding and intermediate annealing
    Xu, Runrun
    Liang, Ningning
    Zhuang, Limin
    Wei, Dajie
    Zhao, Yonghao
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 832
  • [36] Microstructure Evolution and Mechanical Properties of Nano-structured Al-0.2 wt%Zr Alloy Fabricated by Accumulative Roll Bonding (ARB) Process
    Azad, Bahram
    Semnani, Hamidreza Mohammadian
    Borhani, Ehsan
    TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2017, 70 (10) : 2725 - 2732
  • [37] THE EFFECT OF PROLONGED HEAT TREATMENTS ON THE MICROSTRUCTURAL EVOLUTION AND MECHANICAL PROPERTIES OF TI/NI MULTI-LAYERED COMPOSITES FABRICATED BY ACCUMULATIVE ROLL BONDING (ARB)
    Zhang, Bing
    Zhang, Zhijuan
    Zhang, Xunhui
    Yao, Su
    Shang, Xiaodi
    Wang, Wen
    Wang, Le
    Wang, Kuaishe
    Cai, Jun
    ICCM 21: 21ST INTERNATIONAL CONFERENCE ON COMPOSITE MATERIALS (ICCM-21), 2017,
  • [38] Effect of Production Route on the Microstructure and Mechanical Properties of Cu-SiCp Composites
    Balalan, Zulkuf
    Ozgun, Ozgur
    ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING, 2018, 43 (09) : 4889 - 4897
  • [39] Evolution of Microstructure, Mechanical Properties, and Thermal Conductivity of an Al-Li-Cu-Mg-Zr Alloy Processed by Accumulative Roll Bonding (ARB)
    Medjahed, Aboubakr
    Li, Bingcheng
    Hou, Legan
    Wu, Ruizhi
    Zegaoui, Abdeldjalil
    Derradji, Mehdi
    Benyamina, Hocine
    JOM, 2019, 71 (11) : 4096 - 4104
  • [40] Accumulative roll bonding of multilayered Cu/Zn/Al: An evaluation of microstructure and mechanical properties
    Mahdavian, M. M.
    Ghalandari, L.
    Reihanian, M.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2013, 579 : 99 - 107