EFFECT OF BALL-TO-POWDER WEIGHT RATIO ON THE AMORPHIZATION REACTION OF AL50TA50 BY BALL MILLING

被引：33
|
作者：
ELESKANDARANY, MS [1 ]
AOKI, K [1 ]
ITOH, H [1 ]
SUZUKI, K [1 ]
机构：
[1] SUN FRONTIER TECHNOL CO LTD,SENDAI 98202,JAPAN
来源：
JOURNAL OF THE LESS-COMMON METALS | 1991年 / 169卷 / 02期
关键词：
D O I：
10.1016/0022-5088(91)90072-C
中图分类号：
O64 [物理化学（理论化学）、化学物理学];
学科分类号：
070304 ; 081704 ;
摘要：
The present study was undertaken in order to elucidate the effect of the ball-to-powder weight ratio on the amorphization reaction of Al50Ta50 alloy powders using the ball milling technique. As the ball-to-powder weight ratio increases, the rate of amorphization reaction increases drastically, but the content of iron contamination, which comes from the milling tools, increases sharply. A complete amorphous phase is obtained with a ball-to-powder ratio in the range between 36:1 and 108:1 under the present experimental conditions.
引用
收藏
页码：235 / 244
页数：10
相关论文
共 50 条
  • [31] Effect of milling process on microstructural and properties of a ball-milled Al-based nanocomposite powder
    Ramezanalizadeh, Hossein
    ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2022, 8 (02) : 2184 - 2192
  • [32] Mechanically driven solid state amorphization reaction of ball-milled Nb50Zr10Al10Ni10Cu20 powders and the effect of annealing
    Sherif El-Eskandarany, M.
    Matsushita, M.
    Inoue, A.
    Journal of Non-Crystalline Solids, 2002, 312-314 : 622 - 627
  • [33] Mechanically driven solid state amorphization reaction of ball-milled Nb50Zr10Al10Ni10Cu20 powders and the effect of annealing
    El-Eskandarany, MS
    Matsushita, M
    Inoue, A
    JOURNAL OF NON-CRYSTALLINE SOLIDS, 2002, 312-14 : 622 - 627
  • [34] The microstructure and properties of fine crystalline Al-50Si alloy prepared by high-energy ball milling
    MOE Key Laboratory for Nonequilibrium Synthesis and Modulation of Condensed Matter, School of Science, Xi'an Jiaotong University, Xi'an 710049, China
    Cailiao Yanjiu Xuebao, 2009, 5 (495-499):
  • [35] Influence of Milling Time and Ball-to-Powder Ratio on Mechanical Behavior of FeMn30Cu5 Biodegradable Alloys Prepared by Mechanical Alloying and Hot-Forging
    Sivasankaran, Subbarayan
    Ammar, Hany R.
    Almangour, Bandar
    Elborolosy, Samir Ali
    Mekky, Abdel-baset H.
    Alaboodi, Abdulaziz S.
    CRYSTALS, 2022, 12 (12)
  • [36] Effect of ball milling time on Fe2O3/Al nano-composite powder
    Zhou, Chao
    Li, Guo-Ping
    Luo, Yun-Jun
    Guti Huojian Jishu/Journal of Solid Rocket Technology, 2010, 33 (04): : 445 - 448
  • [37] Effect of Ball Milling Technics on Structural Evolution and Uniform Distribution of B 4 C/Al Composite Powder
    Zhang X.
    Cai X.
    Zhou L.
    Qiao Y.
    Wu C.
    Zhang S.
    Zhu W.
    Cailiao Daobao/Materials Review, 2018, 32 (08): : 2653 - 2658
  • [38] Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al2O3 Nanocomposite Synthesized by Ball Milling and Powder Metallurgy
    Toozandehjani, Meysam
    Matori, Khamirul Amin
    Ostovan, Farhad
    Aziz, Sidek Abdul
    Mamat, Md Shuhazlly
    MATERIALS, 2017, 10 (11):
  • [39] Effect of structural evolution of aluminum powder during ball milling on hydrogen generation in aluminum-water reaction
    Razavi-Tousi, S. S.
    Szpunar, J. A.
    INTERNATIONAL JOURNAL OF HYDROGEN ENERGY, 2013, 38 (02) : 795 - 806
  • [40] Preparation of functionally graded materials by pulse current pressure sintering of ball milled Al-50 at% Ti powder
    Nagae, T
    Saji, S
    Yanagimoto, T
    Nose, M
    Yokota, M
    MATERIALS TRANSACTIONS JIM, 2000, 41 (03): : 457 - 460
12345