EFFECT OF A PRESSURE-DEPENDENT VISCOSITY ON THE PACKING STAGE IN INJECTION-MOLDING

被引：5
|
作者：
CHUNG, TS
机构：
来源：
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH | 1987年 / 26卷 / 01期
关键词：
D O I：
10.1021/ie00061a031
中图分类号：
TQ [化学工业];
学科分类号：
0817 ;
摘要：
14
引用
收藏
页码：161 / 163
页数：3
相关论文
共 50 条
  • [21] PROGRESS IN HIGH-PRESSURE INJECTION-MOLDING
    KUBAT, J
    MANSON, JA
    PLASTE UND KAUTSCHUK, 1982, 29 (02): : 91 - 93
  • [22] PRESSURE-INDUCED DENSIFICATION IN INJECTION-MOLDING
    GREENER, J
    POLYMER ENGINEERING AND SCIENCE, 1986, 26 (08): : 534 - 542
  • [23] THE DYNAMICS OF PEAK CAVITY PRESSURE IN INJECTION-MOLDING
    HABER, A
    KAMAL, MR
    POLYMER ENGINEERING AND SCIENCE, 1987, 27 (18): : 1411 - 1418
  • [24] DYNAMICS AND CONTROL OF PRESSURE IN THE INJECTION-MOLDING OF THERMOPLASTICS
    KAMAL, MR
    PATTERSON, WI
    CONLEY, N
    FARA, DA
    LOHFINK, G
    POLYMER ENGINEERING AND SCIENCE, 1987, 27 (18): : 1403 - 1410
  • [25] Morphology evolution during injection molding: effect of packing pressure
    Pantani, R.
    Coccorullo, I.
    Speranza, V.
    Titomanlio, G.
    10TH ESAFORM CONFERENCE ON MATERIAL FORMING, PTS A AND B, 2007, 907 : 969 - +
  • [26] Morphology evolution during injection molding: Effect of packing pressure
    Pantani, R.
    Coccorullo, I.
    Speranza, V.
    Titomanlio, G.
    POLYMER, 2007, 48 (09) : 2778 - 2790
  • [27] EVALUATION PRECISION OF THERMOPLASTIC RESIN VISCOSITY IN INJECTION-MOLDING ANALYSIS
    NAKA, H
    ICHIYANAGI, T
    KENMOCHI, K
    KOBUNSHI RONBUNSHU, 1988, 45 (07) : 561 - 565
  • [28] Numerical simulation of the packing stage in injection molding
    Shen, Changyu
    Zhai, Ming
    Chen, Jingbo
    Liu, Chuntai
    Wang, Lixia
    Gaofenzi Cailiao Kexue Yu Gongcheng/Polymeric Materials Science and Engineering, 2000, 16 (01): : 8 - 10
  • [29] ANALYSIS OF FILLING, PACKING, AND COOLING STAGES IN INJECTION-MOLDING OF DISK CAVITIES
    CHIU, WY
    CHEN, LW
    WANG, C
    WANG, DC
    JOURNAL OF APPLIED POLYMER SCIENCE, 1991, 43 (01) : 39 - 48
  • [30] THERMOSET INJECTION-MOLDING WITH INTERNAL GAS-PRESSURE
    THIENEL, P
    HOSTER, B
    SCHRODER, T
    SCHRODER, K
    KRETSCHMER, J
    LUDWIG, R
    KUNSTSTOFFE-GERMAN PLASTICS, 1993, 83 (02): : 91 - 95
12345