MOLD FILLING IN THE RIM PROCESS

被引：0

作者：

COHNEN, W ^{[1
]}

OSSWALD, TA ^{[1
]}

机构：

[1] UNIV WISCONSIN,FAC MECH ENGN,MADISON,WI 53706

来源：

KUNSTSTOFFE-GERMAN PLASTICS | 1992年 / 82卷 / 11期

关键词：

D O I：

暂无

中图分类号：

TQ [化学工业];

学科分类号：

0817 ;

摘要：

Since the mechanical properties of plastic parts depend to a very high degree on parameters existing during their production, a process optimization based on the mold filling simulation becomes very important. While fairly accurate predictions can be made for injection moulding, currently available mathematical models have not allowed a good enough simulation for the RIM process. This contribution describes a solution to this problem and shows the results from corresponding experimental studies of mould filling.

引用

页码：1127 / 1130

页数：4

共 50 条

[21] Modeling simulation and experimental validation for mold filling process
Hou Hua
Ju Dong-ying
Mao Hong-kui
Saito, D.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, 2006, 16 : S335 - S339
[22] Mold filling Process examined using water as substitute
Xi'an Jiaotong Univ, Xi'an, China
Hsi An Chiao Tung Ta Hsueh, 5 (84-87):
[23] Characteristics and influences factors of mold filling process in permanent mold with a slot gating system
Chang Qingming
Chen Xia
Chen Changjun
Bao Siqian
Schwam, David
CHINA FOUNDRY, 2009, 6 (04) : 328 - 332
[24] Characteristics and influence factors of mold filling process in permanent mold with a slot gating system
David Schwam
ChinaFoundry, 2009, 6 (04) : 328 - 332
[25] C-MOLD simulations of the mold filling process with special consideration of the gates microgeometry
Bikas, A
Kaliora, G
Kanarachos, A
CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS, 1998, 44 : 3522 - 3526
[26] COMPARISON OF RHEOLOGICAL MEASUREMENTS DURING MOLD FILLING FOR GLYCOL AND AMINE EXTENDED URETHANE RIM SYSTEMS
VESPOLI, NP
ALBERINO, LM
ABSTRACTS OF PAPERS OF THE AMERICAN CHEMICAL SOCIETY, 1984, 188 (AUG): : 145 - POLY
[27] Structure of a Viscoplastic Flow During the Mold-Filling Process
E. I. Borzenko
G. R. Shrager
Theoretical Foundations of Chemical Engineering, 2018, 52 : 514 - 524
[28] Simulation of injection-compression mold-filling process
Chen, SC
Chen, YC
Cheng, NT
Huang, MS
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 1998, 25 (07) : 907 - 917
[29] Model experiment of mold filling process in vertical centrifugal casting
Li Changyun
Wu Shiping
Guo Jingjie
Su Yanqing
Bi Weisheng
Fu Hengzhi
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2006, 176 (1-3) : 268 - 272
[30] A Study of the Process of Filling of the Casting Mold in Blank Casting of Uranium
R. G. Belov
Metal Science and Heat Treatment, 2002, 44 : 487 - 490

← 1 2 3 4 5 →