Effect of machining area on material removal rate in strip EDM

被引：0
|
作者：
Ki Young Song
Chong Nam Chu
机构：
[1] Sharp Engineering,Department of Mechanical and Aerospace Engineering
[2] Seoul National University,undefined
来源：
International Journal of Precision Engineering and Manufacturing | 2015年 / 16卷
关键词：
Electrical discharge machining; Electrode; Wear;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
Strip EDM is similar to wire EDM, except that the electrode is a roll of brass strip. In this study, investigated is the effect of machining area on material removal rate (MRR) in strip EDM, The MRR was measured according to different machining areas and different electrical discharge conditions. For a given discharge condition, optimal machining area for maximum MRR was identified. The optimal machining area was larger under higher discharge energy condition. It is shown that strip EDM is much more efficient than wire EDM because material removal rate is much higher and the electrode consumption is much less.
引用
收藏
页码：2435 / 2440
页数：5
相关论文
共 50 条
  • [41] Optimization of process parameters of wire EDM for material removal rate using Taguchi technique
    Kumar, Mandeep
    Singh, Hari
    INDIAN JOURNAL OF ENGINEERING AND MATERIALS SCIENCES, 2016, 23 (04) : 223 - 230
  • [42] Thermal modeling of the material removal rate and surface roughness for die-sinking EDM
    K. Salonitis
    A. Stournaras
    P. Stavropoulos
    G. Chryssolouris
    The International Journal of Advanced Manufacturing Technology, 2009, 40 : 316 - 323
  • [43] Thermal modeling of the material removal rate and surface roughness for die-sinking EDM
    Salonitis, K.
    Stournaras, A.
    Stavropoulos, P.
    Chryssolouris, G.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2009, 40 (3-4): : 316 - 323
  • [44] Investigation of Wire-Cut EDM parameters for machining 2304 duplex stainless steel: effects on material removal rate, surface roughness, and tool wear
    Radhakrishnan, Kamalakkannan
    Kesavalu, Rajmohan
    MATERIA-RIO DE JANEIRO, 2025, 30
  • [45] Characterizing the Effects of Micro Electrical Discharge Machining Parameters on Material Removal Rate during Micro EDM Drilling of Tungsten Carbide (WC-Co)
    Hourmand, Mehdi
    Sarhan, Ahmed A. D.
    Sayuti, Mohd
    5TH ASIA CONFERENCE ON MECHANICAL AND MATERIALS ENGINEERING (ACMME 2017), 2017, 241
  • [46] Robotic material - Removal and machining
    不详
    MANUFACTURING ENGINEERING, 2007, 139 (05): : 83 - +
  • [47] Material removal by spalling during EDM of ceramics
    Trueman, CS
    Huddleston, J
    JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2000, 20 (10) : 1629 - 1635
  • [48] Effect of electrode material on removal efficiency regarding single discharges in wire EDM
    Welschof, Lukas
    Schaefer, Niklas
    Herrig, Tim
    Klink, Andreas
    Bergs, Thomas
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2022, 120 (3-4): : 1583 - 1589
  • [49] Effect of electrode material on removal efficiency regarding single discharges in wire EDM
    Lukas Welschof
    Niklas Schäfer
    Tim Herrig
    Andreas Klink
    Thomas Bergs
    The International Journal of Advanced Manufacturing Technology, 2022, 120 : 1583 - 1589
  • [50] Understanding Material Removal Mechanism and Effects of Machining Parameters during EDM of Zirconia-Toughened Alumina Ceramic
    Bilal, Azat
    Perveen, Asma
    Talamona, Didier
    Jahan, Muhammad Pervej
    MICROMACHINES, 2021, 12 (01) : 1 - 21
12345